Loading…
Derived from what the read produced, so none of it can drift from the data behind it. A blocker stops a price being presented as complete; it never stops you looking. These definitions are this build’s own — no RRE document specifies them yet.
| Check | Status | What the check found |
|---|---|---|
| Sheet scale | pass | All 1 plan sheet(s) carry a scale, so measurement is available. The other 8 read sheet(s) are specifications, schedules and details — nothing is measured on them, so a scale on one is not needed and a scale missing from one is not a gap. |
| Sheets read for scope | warning | 24 sheet(s) were indexed but not read for scope: A000, AS02, A002, A002.1, A002.2, A002.3, D101, D103, D104, D105, D106, A103, A104, A203, A212, A304, M3.0, M5.0, S101, S201, ST0, 001-rocklinelectric.net-Mail---Fwd_-INVITATION-TO-BID---Intimissimi---Roseville-CA-p1, 001-rocklinelectric.net-Mail---Fwd_-INVITATION-TO-BID---Intimissimi---Roseville-CA-p2, 001-rocklinelectric.net-Mail---Fwd_-INVITATION-TO-BID---Intimissimi---Roseville-CA-p3. Looked at by the takeoff and not read: no electrical work on it. Read them, or state the omission on the proposal — the basis of the offer already prints it. |
| Symbol source | warning | No symbol library was found on the drawings, and no engineering firm was identified from the title blocks, so there is no conventions file to fall back on either. This set is read against the default library alone: NECA 100-2006. It is the firm's baseline for what a symbol MEANS where a legend is silent, ambiguous or absent, and it is also the checklist of which symbol categories a plan of this kind ought to show. A line named from the baseline rather than from a legend is named by convention, not by the set. It is reported as 'named from NECA 100, confirm' and carries a semantic-risk flag — a misread convention is a 3× error that no percentage band expresses. Confirm a sample of the named groups on the drawing. Nothing is blocked by this — a default library reads most sets correctly — but a name taken from one is an assumption, and the proposal states it as such. |
| Symbols named | pass | All 364 marks belong to a named group. |
| Every line prices | pass | Every line points at an assembly. |
| Plan and schedule agree | pass | No line has a plan/schedule disagreement. |
| Lines accepted by a person | pass | All 102 eligible line(s) accepted. |
| Engineer conventions known | pass | No engineer-dependent lines. |
| Unsure flags resolved | pass | The model raised no open flags. |
| Cover sheet read | pass | A cover sheet was found and read; its notes parameterise every later pass. |
What the symbol names rest on. No symbol library was found on the drawings, so these names come from NECA 100-2006 rather than from this engineer’s own legend. Confirming a sample on the drawing is worth more here than anywhere else, and each correction is recorded as evidence for the next job.
Edition: 2025 California Electrical Code, because in force for permits from 2026-01-01, as of the bid date 2026-09-29. City and county amendments are the AHJ’s: check them on any job inside a city that amends the code. “To check” means the code requires it and the drawings do not show it: send an RFI, or make the call. Nothing here is added to the bid on its own.
| Section | Status | What the code requires | What the takeoff shows | RRE’s practice |
|---|---|---|---|---|
NEC 2023 250.30 Grounding a transformer (separately derived system) | to check | A transformer secondary is grounded as a separately derived system: a system bonding jumper, a grounding electrode conductor to an electrode, and the supply-side bonding jumper sized from 250.102. | In play for FEEDER WIRE #1 THWN CU (30 KVA XFMR SECONDARY TO PANEL L); FEEDER WIRE #6 THWN CU (PANEL H TO 30 KVA XFMR PRIMARY); GROUND WIRE #10 THWN CU (PANEL H TO XFMR); and 6 more. Nothing on the takeoff shows it. | — |
NEC 2023 300.21 Firestopping at rated penetrations | to check | Electrical penetrations of fire-resistance-rated walls, partitions, floors or ceilings firestopped by an approved method that keeps the rating. | In play for TENMAT FIRE-RATED COVER OVER RECESSED DOWNLIGHT. Nothing on the takeoff shows it. | — |
NEC 2023 406.12 Tamper-resistant receptacles | to check | Tamper-resistant 15- and 20-ampere, 125- and 250-volt receptacles in dwellings, guest rooms and dormitories, child care, preschools and schools, business offices, corridors, waiting rooms, clinics, medical and dental offices, outpatient facilities, assembly occupancies and the other areas the section lists. | In play for DUPLEX RECEPTACLE 20A 125V, WALL. Nothing on the takeoff shows it. |
The RRE item carries no price for the part named, so the estimate has the install labor and rough-in only, and the vendor or sub prices the rest. Send the lighting and gear lists from Material list & vendor quotes.
| Line | Needs a price for | Count | Sheet |
|---|---|---|---|
LIGHT FIXTURE TYPE EM Isolite LMIGN-EM ceiling recessed emergency light 6W, CFCI, unswitched leg (kn 1 / gen e) | LED EMERGENCYLIGHT DUAL | 6 ea | E2.0 |
LIGHT FIXTURE TYPE N Exitronix 902E recessed wall exit sign 5W (sales), CFCI, unswitched leg (kn 1) | LED GRN EXIT FIXTURE | 1 ea | E2.0 |
LIGHT FIXTURE TYPE EX Exitronix GVEX exit sign w/ 90-min battery (BOH), CFCI, unswitched leg | LED GRN EXIT FIXTURE | 1 ea | E2.0 |
| Line | Needs a price for | Count | Sheet |
|---|---|---|---|
PANELBOARD 100A MCB 120/208V 3PH 4W 42 CIRCUIT SURFACE NEMA 1 10KAIC (PANEL L) New Panel L, 42 circuit positions | 100/28 120/208V PNL 3PH | 1 ea | E4.1 |
18 lines the reader wrote at zero are not listed: they add nothing to the bid.
raceway_model.py wire = conductors x path x 1.05 + 2.6 ft makeup per conductor per box. E4.0 upsizing (#10 over 50 ft on 20A) not applied by the model -- runs over 50 ft may go #10. (Model line id L-0073.) The model also raised 'MODELLED', 'E4.0 voltage-drop upsizing not applied', "E4.0 note a: GC provides conductors -- EC is GC's sub", which the contract has no flag for; recorded here rather than dropped.
MODELLED raceway_model.py wire total 2207.3 ft #12 for L-3/5/7/9/11; homeruns all under 50 ft so #12 per E4.0 upsizing table. (Model line id L-0048.)
raceway_model.py on E3.0, 3/8"=1'-0" (27 pt/ft), Panel L located on the plan at its drawn bar in BOH (--panel L), 22 tags read, 17 circuits placed; homerun Manhattan + 10 ft rise + 5 ft stub + drops; includes waste 1.15. MODELLED. (Model line id L-0072.) The model also raised 'MODELLED', 'E3.0 lighting circuits L-3,5,9,11 (lighting plan) not on this sheet', which the contract has no flag for; recorded here rather than dropped.
MODELLED raceway_model.py: Manhattan from Panel L (located on sheet, BOH) through tagged circuits L-3, L-5, L-7, L-9, L-11 (5 circuits, fixtures as stops), chain carried in EMT (set forbids MC). Total 868.6 ft incl. 1.15 waste; model size 1/2" raised to 3/4" per E5.0. (Model line id L-0047.)
E4.0 riser keyed note 4 '(4)#1 THWN, (1)#8 GND IN EXISTING 2" CONDUIT' and note 5 same wire 'IN NEW 2" CONDUIT EXTENDED FROM LANDLORD STUB IN LOCATION TO NEW PANEL LOCATION'. Distance from LL electrical room not shown: firm mall_feeder_default 200 ft allowance x 4 conductors. (Model line id L-0009.) The model also raised 'feeder length not shown - field verify LL room to Panel H', 'E4.0 gen note a: tenant GC provides copper conductors (EC is GC sub)', which the contract has no flag for; recorded here rather than dropped.
E5.0 Raceways 1.9: 'IF A CONDUIT IS SUSPENDED, IT SHALL BE SUPPORTED ON TRAPEZE HANGERS WHICH USE ALL-THREAD RODS FROM THE STRUCTURAL STEEL. THE USE OF CEILING SUPPORT WIRE OR SIMILAR MATERIAL WILL NOT BE ACCEPTED.' trapeze_hanger_rule: carried as a priced hanger system (~0.30-0.35 hr per box point + strut/rod/clamps); Quantity modelled: one trapeze per 10 ft (CEC 358.30 EMT support) of the overhead EMT the plan sheets carry (E2.0 868.6 ft + E3.0 1,109.1 + 35.0 ft; wall stubs excluded). Estimator to add the per-box-point hanger labor. (Model line id L-0099.) The model also raised 'est-review', which the contract has no flag for; recorded here rather than dropped.
Added by kelchlin from a suggestion -- quantity 392 ea ESTIMATED from RRE's ratio, not measured: RRE priced this on 3 of 3 past jobs (100%). RRE’s last restaurant job: 805 straps on 3,183 ft of 3/4" EMT (one per 4 ft); its last retail job 764 on 2,142 ft (one per 2.8 ft). The EMT item carries one per 8 ft, so 0.18 a foot more. Recommended: RRE-EMT-STRAP at 0.03 hr each.
Added by kelchlin from a suggestion -- quantity 373 ft ESTIMATED from RRE's ratio, not measured: RRE priced this on 2 of 3 past jobs (67%). RRE’s last 2 jobs: 2,707 ft of MC luminary 16-2 and 907 ft of 12/3 for 232 whip-fed fixtures (downlights, sconces, emergency, exit, suspended; track heads and strip excluded), measured off the lighting plans as fixture-to-fixture runs. Recommended: RRE-MC-LUM-16-2, priced as RRE bid it at 0.028 hr/ft.
E4.0 keyed notes 4/5 '(1)#8 GND'. 200 ft mall feeder allowance, 1 conductor. (Model line id L-0010.) The model also raised 'feeder length not shown', which the contract has no flag for; recorded here rather than dropped.
Per keyed note 13 callout, 4 conductors on the 35 ft EDH-1 run with route allowance and makeup. (Model line id L-0075.)
Nine ceiling LV positions carried at 12 ft each (no mounting heights given for ceiling devices), two video-wall data at +85" under a 12'-2" ceiling = 5.1 ft each, two storefront data at 12 ft each (no height). Traffic counter conduit excluded: keyed note 1 puts it on GC. Cash desk/IT rack excluded: keyed notes 9, 11 (GC provides (7) 1-1/2" conduits). (Model line id L-0070.) The model also raised 'size not given except WAP 1-1/2" (E1.0 legend); 3/4" assumed for others', 'LV scope UNSURE -- estimator to confirm', which the contract has no flag for; recorded here rather than dropped.
Added by kelchlin from a suggestion -- quantity 125 ft ESTIMATED from RRE's ratio, not measured: RRE priced this on 3 of 3 past jobs (100%). RRE’s last 2 jobs: 2,707 ft of MC luminary 16-2 and 907 ft of 12/3 for 232 whip-fed fixtures (downlights, sconces, emergency, exit, suspended; track heads and strip excluded), measured off the lighting plans as fixture-to-fixture runs. Recommended: RRE-MC-LUM-12-3, priced as RRE bid it at 0.028 hr/ft.
Added by kelchlin from a suggestion -- quantity 85 ea ESTIMATED from RRE's ratio, not measured: RRE priced this on 3 of 3 past jobs (100%). RRE carries MC connectors in step with its luminary cable. Less the ones its branch MC items already carry, about 478 for 2,760 ft on its last retail job and 141 for 853 ft on its last restaurant job (0.17 a foot). Recommended: RRE-MC-CONNECTOR at 0.05 hr each.
RCP general note 2: 'ELECTRICAL CONTRACTOR TO ALLOW TIME FOR DIRECTIONAL ADJUSTMENT FOR ALL LIGHT FIXTURES AS DIRECTED BY OWNER PROJECT MANAGER.' Quantity = the directional fixtures in the A102 equipment legend: 47 KR103 15-degree track spotlights + 9 SLDRT recessed trimless = 56 (matches E2.0 L-0001/L-0002). Fixed 2x2 panels, exits and EM lights (10) excluded as non-adjustable. (Model line id L-0104.) The model also raised 'aiming labour only; not a fixture count', "estimator: add 10 fixed fixtures if 'ALL LIGHT FIXTURES' is read literally", which the contract has no flag for; recorded here rather than dropped.
Counted 47 'T' tags on the E2.0 lighting plan: 13 row 1, 7 row 2, 7 row 3, 12 row 4, 8 on the storefront wall track; A102 legend agrees (47). OFCI per A102. STEP 4.5 RE-COUNT: independent word-level recount of the E2.0 text layer (PDF page 40) finds 47 'T' words, all in the plan cluster; agrees. A (9), BE (1), EM (6, one doubled word at the same point) also agree once legend/title words outside the plan are excluded. (Model line id L-0033.)
Measured the hatched 'TRENCHING LINE BY GC (X-RAY REQUIRED)' on A101 at 3/8"=1'-0" (27 pt/ft): 171.9 pt = 6.37 ft, agrees with the drawn dimension 6'-4 3/8". Multiplied by the (7) 1-1/2" conduits of E3.0 kn 11. (Model line id L-0103.) The model also raised "RESPONSIBILITY: A101 legend 'NEW TRENCHING (X-RAY REQUIRED) BY GC' and 'CABLING FROM FLOOR BY GC'; E3.0 kn 11 'GC TO PROVIDE (7) 1 1/2'' CONDUITS' -- estimator decides whether EC carries this as GC's sub", 'conduit material in slab not stated on A101 (EMT not normally used in slab); check E5.0', which the contract has no flag for; recorded here rather than dropped.
E4.0 keyed note 8 '(4)#1 THWN, (1)#6 GND, 1 1/2" C.' XFMR to Panel L, adjacent in BOH. (Model line id L-0015.)
Model did not place the L-37/39/41 tag; measured Panel L (BOH) to EDH-1 on the plan at 27 pt/ft: 538 pt = 19.9 ft, plus 10 ft rise and 5 ft stub = 35 ft. Callout: (3)#12 THWN + (1)#12 G, 3/4" C. (Model line id L-0074.)
E4.0 keyed note 6 '(3)#6 THWN, (1)#10 GND, 3/4" C.' between Panel H and XFMR; Panel H 1,3,5 wire 6. XFMR drawn beside panels in BOH (E2.0/E3.0) ~10 ft run. (Model line id L-0012.)
OM detail (A213) dimensions the oval mirror 1'-11 5/8" wide x 5'-10 7/8" high and draws a warm LED strip at both edges of the mirror in plan, i.e. around the oval. Ellipse perimeter (Ramanujan) of those dimensions = 13.16 ft per mirror. Places: 2, from the two kn 10 mirror hardwire J-boxes on E3.0. 2 x 13.16 = 26.3 ft. (Model line id L-0105.) The model also raised 'furnish responsibility unconfirmed -- see coverage gap', 'no driver shown', which the contract has no flag for; recorded here rather than dropped.
terminations_per_breaker: one per new circuit the job wires, off E4.1 Panel L. Spares (L-19,25-33,14,16,22; all Panel H 20A) carry no wire and no termination. (Model line id L-0025.)
E4.0 note 5: new 2" conduit from LL stub-in location to new panel location; stub-in location not dimensioned. 20 ft allowance for the in-tenant portion; note 4 portion rides existing 2" conduit (wire only). (Model line id L-0011.) The model also raised 'locate LL stub-in; existing 2" conduit to be verified reusable', which the contract has no flag for; recorded here rather than dropped.
A401 Detail 1 Light Fixture Support, Fig 6.4.9.1-7 'Recessed light fixture in suspended ceiling (fixture weight < 10 pounds)': '#12 safety wire one per fixture < 10#', '3/8" expansion anchor with tie-wire head ... for attachment to structure', '1-1/2" 3 turns min.' each end; 'Ceiling construction (gypboard shown, acoustic ceiling similar)'. 1 wire x 15 recessed ceiling fixtures in the gyp ceiling per E2.0 (A 9, EM 6; A102 legend shows EM 5). A 17W trimless and EM 6W assumed under 10 lb. Wall-recessed exits N/EX and owner speakers excluded. (Model line id L-0106.) The model also raised 'est-review', 'if any fixture is 10-56 lb Fig 6.4.9.1-8 applies: 2 slack wires at diagonal corners', 'wire feet not measured -- see coverage gap', which the contract has no flag for; recorded here rather than dropped.
Keyed note 17 calls 1/2" conduit to above ceiling with pull string: thermostat at 48" in corridor (ceiling 9'-10") 5.8 ft, remote sensor at 60" in sales (ceiling 12'-2") 7.2 ft = 13.0 ft. (Model line id L-0065.)
Counted 12 duplex receptacle symbols (8-pt circle, two bars) on the E3.0 power plan by circuit: L-2 2, L-24 2, L-17 1, L-15 4 (two stacked at each storefront bulkhead, +133" AFF), L-4 3. (Model line id L-0049.)
A401 Detail 6 sub-detail D 'Light Fixture Attachment Detail': 'SUPPLEMENTAL 12 GA HANGER WIRE AT EA CORNER OF FIXTURE', 'LIGHT FIXTURE 20 LBS OR LESS THAN', 'ATTACH LIGHT FIXTURE TO CEILING GRID'; sub-detail A hanger wire tie 'MIN. 3 TIGHT FULL TURNS IN 3" AT EA. WIRE END'. 4 corners x 3 lay-in 2x2 fixtures in the BOH ACT ceiling per E2.0 (B 2, BE 1) = 12 wires. (Model line id L-0107.) The model also raised 'est-review', 'elevation view shows 2 wires; 6 total if read as 2 per fixture (Fig 6.4.9.1-8 diagonal corners)', 'wire feet not measured -- see coverage gap', which the contract has no flag for; recorded here rather than dropped.
E4.0 keyed note 6. (Model line id L-0013.)
E4.0 keyed note 6 '3/4" C.'; ~10 ft, equipment adjacent in BOH. (Model line id L-0014.)
E4.0 keyed note 8. (Model line id L-0016.)
E4.0 keyed note 8 '1 1/2" C.' (Model line id L-0017.)
Counted 9 'A' tags: 4 ADA fitting room, 2 corridor, 3 storefront wall; A102 (9) and E6.0 (9) agree. OFCI. (Model line id L-0034.)
Added by kelchlin from a suggestion -- quantity 9 ea ESTIMATED from RRE's ratio, not measured: RRE priced this on 1 of 3 past jobs (33%). RRE’s last retail job: 79 Tenmat FF109-300 covers for its 79 recessed downlights, one each, at 0.10 hr and $8.66. Recommended: RRE-TENMAT, priced as RRE bid it.
House standard safe_off 8 hr TI (3/3 blind jobs exact). Existing tenant lighting/power shown on D102; D-sheet demo note 4 disconnects circuits at source. Safe-off only - removal is by others. (Model line id L-0030.)
E5.0 Nameplates 1.1: furnish and mount a nameplate on each panelboard, safety switch, starter, remote control and similar control; 3.10 phenolic labels for each panel. Count of 8 is the equipment list in job facts (Panels H, L, XFMR, EDH-1 disc, VAV-1 switch, sign disc, TC1, current-limiting panel). (Model line id L-0101.)
Counted 6 'EM' fixtures (boxed EM with keyed note 1): fitting room 1, sales 4; A102 agrees (5). (Model line id L-0039.)
One feed point per drawn track run (6 runs); circuits L-5 (general), L-9 (wall), L-3 (show window) via current limiting panel. (Model line id L-0041.)
Six pairs of receptacle circles, one pair per circuit tag: cash desk L-6, L-8, L-10, L-12 and IT rack wall in BOH L-18, L-20 (scanner group of 12 circles, two per pair). (Model line id L-0052.) The model also raised 'pair of circles per circuit read as one double duplex; could be two separate duplex -- confirm', 'cash desk receptacles may be inside GC millwork (kn 11 puts device J-boxes in cash desk by GC)', which the contract has no flag for; recorded here rather than dropped.
ST1 detail 12 (suspended ceiling seismic), ceiling note 4: 'AT LIGHT FIXTURES PROVIDE #12 GALV. WIRE AT DIAGONAL OPPOSED' corners = 2 wires per lay-in fixture. Places: the only fixtures in the T-bar (AC-1) ceiling are the BOH 2x2 panels, B = 2 and BE = 1 as counted on E2.0 (L-0003, L-0004). 3 x 2 = 6 wires. Fixtures themselves are not re-taken here. (Model line id L-0108.) The model also raised 'party for fixture wires not named on ST1 -- see coverage gap', which the contract has no flag for; recorded here rather than dropped.
Five speaker symbols each with keyed note 6 'PROVIDE JUNCTION BOX ABOVE CEILING FOR MUSIC CABLE' (sales front, corridor, BOH/sales rear, sales centre, sales rear right). A102 lists 3 speakers -- plan governs. (Model line id L-0066.) The model also raised 'A102 legend lists 3 speakers vs 5 drawn here', which the contract has no flag for; recorded here rather than dropped.
E4.0 notes 2/4/5/8: service feeder ends at existing 100A CB and Panel H 100A MCB; secondary feeder ends at XFMR X-terminals and Panel L 100A MCB. (Model line id L-0028.)
Filled-triangle data symbols: 2 beside the L-17 video wall receptacle at +85" AFF and 2 beside the L-15/L-21 storefront bulkhead. Cash desk (26) and IT rack (12) triangles are GC scope by keyed notes 9 and 11 and are not carried. (Model line id L-0069.) The model also raised 'LV cabling scope UNSURE per job facts', which the contract has no flag for; recorded here rather than dropped.
E4.0 Switchbank Detail (detail 2) draws 5 switch positions, each a switch with a slide dimmer; 'a','b','c' at +48" AFF (sales / fitting room) and 'd' at +42" AFF (sales wall display track); '**PROVIDE PILOT LIGHT ON SWITCHES TO INDICATE LIGHT STATUS'. Lighting Control Diagram (detail 3) wires a-d through TC1 to L-5, L-7, L-7, L-9. 'e' is the occupancy sensor switch, its own line. These are the same switches the E2.0 lighting plan draws at the switchbanks -- keep one count, this detail gives the type. Striking it removes 4 dimmers. STEP 4.5: E2.0 counted the same switchbank devices (L-0043/L-0044) as plain/OS switches; E4.0's lighting-control schedule names them dimmers, so they are carried once, here. (Model line id L-0086.) The model also raised 'possible_duplicate_with_E2.0', which the contract has no flag for; recorded here rather than dropped.
Three camera symbols with keyed note 5: at the fitting-room entry and at both rear corners of sales. (Model line id L-0068.)
One per hard-wired HVAC unit (EDH-1, VAV-1) per equipment_disconnect_at_every_unit and house whip rule; E5.0 1.5 requires liquid-tight metal conduit to motors/vibrating equipment. Interior units - no NEMA 3R. STEP 4.5: M1.0 re-counted the VAV-1 and EDH-1 connections (L-0112, L-0113), struck as duplicates of this line. (Model line id L-0021.)
E4.1 Panel H 3/50 wire 6; E4.0 kn 6. One at breaker, one at XFMR primary. (Model line id L-0027.)
E4.0 general note g. (Model line id L-0032.)
Counted 2 'B' tags in BOH; A102 agrees (2). (Model line id L-0035.)
Two receptacles at the storefront display platforms tagged L-13 with keyed notes 3 and 4 (inside platform, routed through the time clock). (Model line id L-0050.)
Two show-window receptacle symbols (slashed circle) at the storefront windows, tagged L-21, keyed note 2. (Model line id L-0051.) The model also raised 'symbol is a slashed circle; ceiling vs wall mounting for show window to confirm on E4.0 detail', which the contract has no flag for; recorded here rather than dropped.
Two boxes at +48" AFF in the ADA fitting room with keyed note 10 hexes, tagged L-7. (Model line id L-0054.)
Connection at each of the two kn 10 mirror J-boxes (job-facts hard-wired equipment). (Model line id L-0055.)
T and S symbols with keyed note 17 hexes: thermostat J-box at 48" AFF in the corridor, remote sensor at 60" AFF on the sales front wall. (Model line id L-0064.)
E4.1 Panel H header: 277/480V 3PH 4W, mains 100A MCB, surface, NEMA 1, 22KAIC; E4.0 riser '(N)PANEL H 480/277V'. Located BOH per E2.0/E3.0. (Model line id L-0001.)
E4.1 Panel L header: 120/208V 3PH 4W, mains 100A MCB, surface, NEMA 1, 10KAIC, circuits 1-42; E4.0 riser '(N)PANEL L 120/208V'. (Model line id L-0002.)
E4.0 riser '(N)30 KVA TRANS.' between Panel H (H-1,3,5 3P 50A) and Panel L; drawn as '30KVA XFMR' in BOH on E2.0/E3.0. Mounting (floor/wall) not detailed. (Model line id L-0003.) The model also raised 'mounting and any wall bracket not shown', which the contract has no flag for; recorded here rather than dropped.
E3.0 keyed note 13 'PROVIDE 30/3/15A FUSED DISCONNECT FOR EDH-1. CONNECT TO CIRCUIT INDICATED USING (3)#12 THWN, (1)#12 GND, 3/4" CONDUIT.' Fused per the callout; interior above ceiling (NEMA 1). Fuses 15A x3. STEP 4.5 DISCONNECT CHECK: no equipment schedule for EDH-1 was available to the re-read (output/work/equipment/ was not produced; the M1.0 schedules are raster), so the switch could not be re-sized from the unit's MOCP. Line kept as first read; see coverage gap. (Model line id L-0019.) The model also raised 'disconnect not sized from schedule MOCP', which the contract has no flag for; recorded here rather than dropped.
E3.0 keyed note 12 'PROVIDE MOTOR RATED SWITCH FOR VAV-1 DISCONNECT. CONNECT TO CIRCUIT INDICATED USING (2)#12 THWN, (1)#12 GND, 3/4" CONDUIT.' Panel L-35 20/1, 200 W. Non-fused; interior. STEP 4.5 DISCONNECT CHECK: no equipment schedule for VAV-1 was available to the re-read (output/work/equipment/ was not produced; the M1.0 schedules are raster), so the switch could not be re-sized from the unit's MOCP. Line kept as first read; see coverage gap. (Model line id L-0020.) The model also raised 'disconnect not sized from schedule MOCP', which the contract has no flag for; recorded here rather than dropped.
E3.0 keyed note 16: J-box within 5 ft of sign, 'PROVIDE DISCONNECT AS REQUIRED', route through timeclock. Sign is interior behind storefront glazing (A102 'NEW INTIMISSIMI LED SIGN'); switch type not specified. STEP 4.5 DISCONNECT CHECK: no equipment schedule for STOREFRONT SIGN was available to the re-read (output/work/equipment/ was not produced; the M1.0 schedules are raster), so the switch could not be re-sized from the unit's MOCP. Line kept as first read; see coverage gap. (Model line id L-0022.) The model also raised 'confirm with sign vendor whether sign has integral disconnect', 'disconnect not sized from schedule MOCP', which the contract has no flag for; recorded here rather than dropped.
E4.0 lighting control diagram: TC1 24HR/7DAY astronomical time clock Intermatic ET91215CR, outputs L-1,3,13,15,17,21 + 3 spares, override switch at storefront; Panel L REM TC on L-1,3,5,7,9,13,15,17,21. (Model line id L-0023.) The model also raised '9+ circuits on one time clock: a lighting contactor/relay panel is implied but not shown - verify with controls vendor', which the contract has no flag for; recorded here rather than dropped.
E2.0 keyed note 4 'PROVIDE CURRENT LIMITING PANEL FOR TRACK LIGHTING CIRCUITS'; schedule: switch a L-5 4A GENERAL, d L-9 6A WALL, tc L-3 2A SHOW WINDOW. E6.0 NRCC Table G checks 'ii Current Limiter'. (Model line id L-0024.) The model also raised 'house default: controls hardware vendor quote - confirm who furnishes the limiter panel', which the contract has no flag for; recorded here rather than dropped.
E4.1 Panel L 3/15 EDH-1; (3)#12 + #12G per E3.0 kn 13. (Model line id L-0026.)
1 'BE' tag in BOH (the 'EM' under it is its battery sub-label, not a separate EM unit); A102 agrees. (Model line id L-0036.)
1 'N' tag at storefront side of sales area. (Model line id L-0037.)
1 'EX' tag at BOH door (keyed note 1). (Model line id L-0038.)
'S' with keyed note 5 at storefront entry. STEP 4.5: E4.0 counts the same storefront 0-2 hr override (L-0092, struck as duplicate); carried once here. (Model line id L-0045.)
'S' with keyed note 6 by Panels L/H in BOH. (Model line id L-0046.)
One receptacle at VAV-1/EDH-1 tagged L-23 with keyed note 15: 'PROVIDE GFCI DUPLEX RECEPTACLE FOR HVAC EQUIPMENT'. GFCI carried at the device. (Model line id L-0053.)
One J-box at the storefront, tagged L-1, +145" AFF, keyed note 16. (Model line id L-0056.)
'J' symbol at VAV-1 above ceiling, L-35. (Model line id L-0059.)
EDH-1 is hard-wired equipment (job facts); connection carried at the unit beside its disconnect. (Model line id L-0061.)
Keyed note 14 at the VAV-1/EDH-1 group: 'PROVIDE LED VAPORTIGHT LIGHT FIXTURE FOR MAINTENANCE'. Not in the fixture schedule; circuit not tagged (assume L-23). (Model line id L-0062.) The model also raised 'fixture not scheduled -- type/wattage to confirm', which the contract has no flag for; recorded here rather than dropped.
Keyed note 14: 'PROVIDE LOCAL CONTROL SWITCH AT ACCESS ENTRY'; no switch symbol drawn, location field-set. (Model line id L-0063.)
One WAP symbol with keyed note 7 in the sales area beside the cash desk. (Model line id L-0067.)
Filled dot with keyed note 8 inside the cash desk island. (Model line id L-0071.) The model also raised 'size and length not given; trench scope to confirm', which the contract has no flag for; recorded here rather than dropped.
E4.0 Switchbank Detail draws BOH 'e' at +42" AFF with a slide; Lighting Control Diagram labels it 'OCCUPANCY SENSOR SWITCH e' feeding L-11 BOH LIGHTS. Same device the E2.0 plan draws; keep one. Striking it removes the BOH sensor switch. STEP 4.5: E2.0 counted the same switchbank devices (L-0043/L-0044) as plain/OS switches; E4.0's lighting-control schedule names them dimmers, so they are carried once, here. (Model line id L-0087.) The model also raised 'possible_duplicate_with_E2.0', which the contract has no flag for; recorded here rather than dropped.
Switchbank Detail draws a, b, c ganged in one bank at +48" AFF: one 3-gang box. Striking it removes the box; the dimmers stay. (Model line id L-0088.)
Switchbank Detail draws 'd' (sales wall display) and 'e' (BOH) side by side in one bank at +42" AFF: one 2-gang box. If field puts d and e on different sides of the BOH door (they serve different rooms) this becomes two 1-gang boxes -- confirm on E2.0. (Model line id L-0089.) The model also raised 'confirm_ganging', which the contract has no flag for; recorded here rather than dropped.
TC1 is hard-wired control gear (job-facts.md 'Hard-wired equipment'); no J-box symbol is drawn on the diagram, so one J-box and connection is carried at it (hardwired_equipment_jbox). The controlled circuits' conductors through TC1 are in the E2.0/E3.0 branch runs. (Model line id L-0091.)
E5.0 Distribution Panels 3.12: 'SURFACE-MOUNTED PANELS SHALL BE MOUNTED ON A 3/4" PLYWOOD BACKBOARD.' Job facts: Panel H and Panel L are surface NEMA 1 in BOH side by side with TC1 and the current-limiting panel; one 4x8 sheet assumed. (Model line id L-0100.)
E5.0 Scope 5.1h 'TESTING OF ALL CABLES AND CIRCUIT WIRING AFTER INSTALLATION'; Panelboards 2.9 'AT COMPLETION OF JOB, ELECTRICAL CONTRACTOR SHALL TAKE CURRENT READING CHECK...'. Commissioning is the owner's (spec basic materials; E2.0 h), so no acceptance/commissioning lot. (Model line id L-0102.)
AS01 Turnover Requirements item 5: 'THE CONTRACTOR SHALL SET ALL TIME CLOCKS, THERMOSTATS ETC. PER THE OWNERS REPRESENTATIVE AND PROVIDING COPIES OF OPERATION, MAINTENANCE OR A WARRANTY MANUAL.' The only time clock in the set is TC1 (E2.0/E4.0, job facts), installed by the EC; programming its schedule (sign L-1, storefront L-3, L-5/7/9 lighting, L-13/15/17/21 receptacles) falls to the EC. Quantity 1 = TC1. Labor only - the clock itself is carried from the E sheets. (Model line id L-0110.) The model also raised 'labor-only', 'dedupe: TC1 device is an E-sheet line; this is the set-up/programming only', which the contract has no flag for; recorded here rather than dropped.
AS01 Punch List item 5: 'ELECTRICAL: ALL SYSTEMS IN OPERATING CONDITION, COMPLETE WITH TRIM; ALL LIGHT FIXTURES OPERABLE WITH LAMPS AND LENSES, MAINTENANCE DATA.' and Turnover item 5 (copies of operation, maintenance and warranty manuals). Falls on the EC for Div 26 work. Commissioning itself is the owner's (E2.0 h), not carried. (Model line id L-0111.) The model also raised 'labor-only', which the contract has no flag for; recorded here rather than dropped.
Added by kelchlin from a suggestion: RRE priced this on 3 of 3 past jobs (100%). RRE’s last retail job and last restaurant job carried these items at identical quantities -- a fixed allowance, not a count (33.4 hr, $732). Recommended: RRE-HOUSE-KIT, once per job.
Added by kelchlin from a suggestion: RRE priced this on 3 of 4 past jobs (75%). RRE carried these at exactly these quantities on its two larger jobs (22.0 hr, $150), and about an eighth of them, with no backboard, on its smallest. Recommended: RRE-HOUSE-KIT-LOOSE on a job of restaurant or larger-retail size; leave it off a small fit-out.
| — |
NEC 2023 110.16 Arc-flash warning label on gear | shown | Switchboards, switchgear, panelboards, meter socket enclosures and motor control centers likely to be worked on energized carry a field- or factory-applied arc-flash hazard warning. | In play for PANEL DIRECTORIES / CIRCUIT IDENTIFICATION; PANELBOARD 100A MCB 277/480V 3PH 4W SURFACE NEMA 1 22KAIC (PANEL H); PANELBOARD 100A MCB 120/208V 3PH 4W 42 CIRCUIT SURFACE NEMA 1 10KAIC (PANEL L). Shown: ENGRAVED PHENOLIC NAMEPLATE, BLACK/WHITE (spec nameplates 1.1, 3.10). | RRE carries phenolic nameplates and labels as their own item where the set calls for them. |
NEC 2023 210.62 Receptacles in show windows | shown | At least one 125-volt receptacle within 18 in. of the top of a show window for each 12 linear ft of show window. | In play for DUPLEX RECEPTACLE 20A, SHOW WINDOW (kn 2). Shown: DUPLEX RECEPTACLE 20A, SHOW WINDOW (kn 2). | — |
NEC 2023 300.11, 410.36(B) Support in suspended ceilings | shown | Raceways, cables and boxes above a suspended ceiling are supported independently of the ceiling grid, or by identified support wires; lay-in luminaires are fastened to the grid framing. | In play for #12 GA SUPPLEMENTAL HANGER WIRE AT EACH CORNER OF 2x2 LAY-IN FIXTURE, ACT GRID TO STRUCTURE, 3 TIGHT TURNS IN 3" (fixture <= 20 lb); LIGHT FIXTURE SEISMIC SUPPORT WIRE, #12 GALV. STEEL, TIED TO STRUCTURE, DIAGONAL OPPOSED CORNERS, 2x2 LAY-IN FIXTURE IN T-BAR (ACT) CEILING; LIGHT FIXTURE TYPE B; and 1 more. Shown: 1-5/8" STRUT CHANNEL, TRAPEZE HANGER CROSSMEMBERS ON 3/8" ALL-THREAD PAIRS FROM STRUCTURE (spec raceway 1.9); #12 GA SEISMIC SAFETY WIRE, RECESSED FIXTURE TO STRUCTURE, 3 TURNS IN 1-1/2" EACH END, W/ 3/8" EXPANSION ANCHOR OR TIE-OFF AT STRUCTURE (1 per fixture < 10 lb, gyp ceiling); #12 GA SUPPLEMENTAL HANGER WIRE AT EACH CORNER OF 2x2 LAY-IN FIXTURE, ACT GRID TO STRUCTURE, 3 TIGHT TURNS IN 3" (fixture <= 20 lb); and 1 more. | RRE carries the fixture support wire as its own item where the ceiling is a grid. |
NEC 2023 408.4(A) Circuit directory at every panel | shown | Every circuit and circuit modification legibly identified as to its clear, evident and specific purpose on a circuit directory at the panel. | In play for PANEL DIRECTORIES / CIRCUIT IDENTIFICATION; PANELBOARD 100A MCB 277/480V 3PH 4W SURFACE NEMA 1 22KAIC (PANEL H); PANELBOARD 100A MCB 120/208V 3PH 4W 42 CIRCUIT SURFACE NEMA 1 10KAIC (PANEL L). Shown: PANEL DIRECTORIES / CIRCUIT IDENTIFICATION. | RRE carries a panel directory update where circuits land in an existing panel. |
NEC 2023 422.31, 424.19, 430.102 Disconnect for water heaters, heaters, fans and motor loads | shown | A disconnect within sight of the appliance, heater or motor, or a branch-circuit breaker that can be locked in the open position. | In play for ENGRAVED PHENOLIC NAMEPLATE, BLACK/WHITE (spec nameplates 1.1, 3.10); FUSED DISCONNECT SWITCH 30A 3-POLE 240V NEMA 1 WITH (3) 15A FUSES (EDH-1); MOTOR RATED SWITCH 1-POLE 20A 120V NEMA 1 (VAV-1 DISCONNECT); and 1 more. Shown: 3/4" EMT, EDH-1 BRANCH L-37/39/41 (kn 13); ENGRAVED PHENOLIC NAMEPLATE, BLACK/WHITE (spec nameplates 1.1, 3.10); EQUIPMENT CONNECTION 6 FT 3/4" LIQUID-TIGHT FLEX WHIP (EDH-1, VAV-1); and 2 more. | A lockable breaker answers it as well as a switch: check the panel schedule before adding a disconnect. |
NEC 2023 450.3(B) Transformer overcurrent protection | shown | Primary (and where used, secondary) overcurrent protection for each transformer within the percentages of Table 450.3(B), and the secondary conductors protected per 240.21(C). | In play for FEEDER WIRE #1 THWN CU (30 KVA XFMR SECONDARY TO PANEL L); FEEDER WIRE #6 THWN CU (PANEL H TO 30 KVA XFMR PRIMARY); GROUND WIRE #10 THWN CU (PANEL H TO XFMR); and 6 more. Shown: FEEDER WIRE #1 THWN CU (30 KVA XFMR SECONDARY TO PANEL L); FEEDER WIRE #6 THWN CU (PANEL H TO 30 KVA XFMR PRIMARY); 3/4" EMT CONDUIT (PANEL H TO XFMR PRIMARY); and 4 more. | — |
NEC 2023 600.5(A) Sign outlet at each tenant entrance | shown | At least one outlet at each entrance to each tenant space accessible to pedestrians, for a sign, on a 20-ampere branch circuit that supplies no other load. | Shown: ENGRAVED PHENOLIC NAMEPLATE, BLACK/WHITE (spec nameplates 1.1, 3.10); SIGN DISCONNECT SWITCH 20A 1-POLE 120V (STOREFRONT SIGN, AS REQUIRED); JUNCTION BOX, STOREFRONT SIGN +145" AFF (kn 16). | RRE prices "power to building signage" where the set shows it; the matrix row is left blank where it does not. |
NEC 2023 600.6 Disconnect within sight of a sign | shown | Each sign or outline lighting system, or its feeder, has an externally operable disconnect within sight of the sign, or one capable of being locked in the open position. | In play for ENGRAVED PHENOLIC NAMEPLATE, BLACK/WHITE (spec nameplates 1.1, 3.10); SIGN DISCONNECT SWITCH 20A 1-POLE 120V (STOREFRONT SIGN, AS REQUIRED); JUNCTION BOX, STOREFRONT SIGN +145" AFF (kn 16). Shown: 3/4" EMT, EDH-1 BRANCH L-37/39/41 (kn 13); ENGRAVED PHENOLIC NAMEPLATE, BLACK/WHITE (spec nameplates 1.1, 3.10); EQUIPMENT CONNECTION 6 FT 3/4" LIQUID-TIGHT FLEX WHIP (EDH-1, VAV-1); and 3 more. | RRE prices a WP switch at signage as a fused disconnect assembly (firm practice wp_switch_mapping). |
A takeoff cannot settle every article: load calculations and coordination are the engineer of record’s, and workmanship is the inspector’s. Each is listed so nothing is silently skipped. “Waiting on a code read” means the article is in play and this job’s drawing read has not been checked against the code yet: re-run the read, or check it on the drawings.
| 90 | Introduction | general | Scope and definitions: nothing to check on a job. |
| 100 | Definitions | general | Scope and definitions: nothing to check on a job. |
| 110 | Requirements for Electrical Installations | checked | 1 section checked against the takeoff, all shown. |
| 200 | Use and Identification of Grounded Conductors | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 210 | Branch Circuits | checked | 1 section checked against the takeoff, all shown. |
| 215 | Feeders | checked | In play; none of its checked sections applies to these lines. |
| 220 | Branch-Circuit, Feeder, and Service Load Calculations | design | The engineer of record’s: sizing, calculation or coordination, not checked against a takeoff. |
| 225 | Outside Branch Circuits and Feeders | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 230 | Services | checked | In play; none of its checked sections applies to these lines. |
| 235 | Branch Circuits, Feeders, and Services Over 1000 Volts ac, 1500 Volts dc | not in play | Nothing on this takeoff puts it in play. |
| 240 | Overcurrent Protection | checked | In play; none of its checked sections applies to these lines. |
| 242 | Overvoltage Protection | not in play | Nothing on this takeoff puts it in play. |
| 245 | Overcurrent Protection for Systems Rated Over 1000 Volts ac, 1500 Volts dc | not in play | Nothing on this takeoff puts it in play. |
| 250 | Grounding and Bonding | to check | 1 section checked against the takeoff, 1 to check: 250.30. |
| 300 | General Requirements for Wiring Methods and Materials | to check | 2 sections checked against the takeoff, 1 to check: 300.21. |
| 305 | General Requirements for Wiring Methods and Materials for Systems Rated Over 1000 Volts ac, 1500 Volts dc | not in play | Nothing on this takeoff puts it in play. |
| 310 | Conductors for General Wiring | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 312 | Cabinets, Cutout Boxes, and Meter Socket Enclosures | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 314 | Outlet, Device, Pull, and Junction Boxes; Conduit Bodies; Fittings; and Handhole Enclosures | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 315 | Medium Voltage Conductors, Cable, Cable Joints, and Cable Terminations | not in play | Nothing on this takeoff puts it in play. |
| 320 | Armored Cable: Type AC | not in play | Nothing on this takeoff puts it in play. |
| 322 | Flat Cable Assemblies: Type FC | not in play | Nothing on this takeoff puts it in play. |
| 324 | Flat Conductor Cable: Type FCC | not in play |
| 400 | Flexible Cords and Flexible Cables | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 402 | Fixture Wires | not in play | Nothing on this takeoff puts it in play. |
| 404 | Switches | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 406 | Receptacles, Cord Connectors, and Attachment Plugs (Caps) | to check | 1 section checked against the takeoff, 1 to check: 406.12. |
| 408 | Switchboards, Switchgear, and Panelboards | checked | 1 section checked against the takeoff, all shown. |
| 409 | Industrial Control Panels | not in play | Nothing on this takeoff puts it in play. |
| 410 | Luminaires, Lampholders, and Lamps | checked | In play; none of its checked sections applies to these lines. |
| 411 | Low-Voltage Lighting | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 422 | Appliances | checked | 1 section checked against the takeoff, all shown. |
| 424 | Fixed Electric Space-Heating Equipment |
| 500 | Hazardous (Classified) Locations, Classes I, II, and III, Divisions 1 and 2 | not in play | Nothing on this takeoff puts it in play. |
| 501 | Class I Hazardous (Classified) Locations | not in play | Nothing on this takeoff puts it in play. |
| 502 | Class II Hazardous (Classified) Locations | not in play | Nothing on this takeoff puts it in play. |
| 503 | Class III Hazardous (Classified) Locations | not in play | Nothing on this takeoff puts it in play. |
| 504 | Intrinsically Safe Systems | not in play | Nothing on this takeoff puts it in play. |
| 505 | Zone 0, 1, and 2 Locations | not in play | Nothing on this takeoff puts it in play. |
| 506 | Zone 20, 21, and 22 Locations for Combustible Dusts or Ignitible Fibers/Flyings | not in play | Nothing on this takeoff puts it in play. |
| 510 | Hazardous (Classified) Locations — Specific | not in play | Nothing on this takeoff puts it in play. |
| 511 | Commercial Garages, Repair and Storage | not in play | Nothing on this takeoff puts it in play. |
| 513 | Aircraft Hangars | not in play |
| 600 | Electric Signs and Outline Lighting | checked | 2 sections checked against the takeoff, all shown. |
| 604 | Manufactured Wiring Systems | not in play | Nothing on this takeoff puts it in play. |
| 605 | Office Furnishings | not in play | Nothing on this takeoff puts it in play. |
| 610 | Cranes and Hoists | not in play | Nothing on this takeoff puts it in play. |
| 620 | Elevators, Dumbwaiters, Escalators, Moving Walks, Platform Lifts, and Stairway Chairlifts | not in play | Nothing on this takeoff puts it in play. |
| 625 | Electric Vehicle Power Transfer System | not in play | Nothing on this takeoff puts it in play. |
| 626 | Electrified Truck Parking Spaces | not in play | Nothing on this takeoff puts it in play. |
| 630 | Electric Welders | not in play | Nothing on this takeoff puts it in play. |
| 640 | Audio Signal Processing, Amplification, and Reproduction Equipment | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 645 | Information Technology Equipment |
| 700 | Emergency Systems | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 701 | Legally Required Standby Systems | not in play | Nothing on this takeoff puts it in play. |
| 702 | Optional Standby Systems | not in play | Nothing on this takeoff puts it in play. |
| 705 | Interconnected Electric Power Production Sources | not in play | Nothing on this takeoff puts it in play. |
| 706 | Energy Storage Systems | not in play | Nothing on this takeoff puts it in play. |
| 708 | Critical Operations Power Systems (COPS) | not in play | Nothing on this takeoff puts it in play. |
| 710 | Stand-Alone Systems | not in play | Nothing on this takeoff puts it in play. |
| 712 | Direct Current Microgrids | not in play | Nothing on this takeoff puts it in play. |
| 722 | Cables for Power-Limited Circuits and Fault-Managed Power Circuits | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 724 | Class 1 Power-Limited Circuits and Class 1 Power-Limited Remote-Control and Signaling Circuits |
| 800 | General Requirements for Communications Systems | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 805 | Communications Circuits | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 810 | Radio and Television Antenna Equipment | not in play | Nothing on this takeoff puts it in play. |
| 820 | Community Antenna Television and Radio Distribution Systems | not in play | Nothing on this takeoff puts it in play. |
| 830 | Network-Powered Broadband Communications Systems | not in play | Nothing on this takeoff puts it in play. |
| 840 | Premises-Powered Broadband Communications Systems | not in play | Nothing on this takeoff puts it in play. |
| Ch. 9 | Tables: conduit fill, conductor properties, power-limited sources | checked | In play; none of its checked sections applies to these lines. |
| Line |
|---|
| Needs a price for |
|---|
| Count |
|---|
| Sheet |
|---|
TIME CLOCK 24 HR / 7 DAY ASTRONOMICAL (INTERMATIC ET91215CR OR EQUAL) TC1 Controls L-1,3,5,7,9,13,15,17,21 (REM TC) + 3 spares | 208/277V 24HR DPST 40A | 1 ea | E4.0 |
TIME CLOCK SET-UP AND PROGRAMMING - TC1 Intermatic ET91215CR astronomical time clock, 0-2 hr storefront override Set all time clocks per the owner's representative at turnover (AS01 Turnover Requirements 5); thermostats in the same note are the mechanical contractor's. | 208/277V 24HR DPST 40A | 1 ea | A101 |
Read off the schedules and notes. RRE buys none of the material named here. Check each against the responsibility matrix on the proposal: these are what it should say is by others.
| Line | Furnished by | Installed by | RRE’s part | Sheet |
|---|---|---|---|---|
LIGHT FIXTURE AIMING / DIRECTIONAL ADJUSTMENT, TRACK SPOTLIGHT TYPE T (KR103) AND RECESSED TYPE A (SLDRT), AS DIRECTED BY OWNER PM The drawings say “by owner”. | Owner | not stated | RRE installs / connects only | A101 |
LIGHT FIXTURE TYPE T The drawings say “owner furnished”. | Owner | not stated | RRE installs / connects only | E2.0 |
1-1/2" CONDUIT IN SLAB TRENCH, (7) RUNS, BOH WALL TO CASH DESK STUB-UP (horizontal in-slab run only) The drawings say “by gc”. | GC | not stated | RRE installs / connects only | A101 |
LED STRIP LIGHT, WARM WHITE, CONCEALED AROUND OVAL MIRROR PERIMETER (OM detail) The drawings say “owner-furnished”. | Owner | not stated | RRE installs / connects only | A213 |
LIGHT FIXTURE TYPE A The drawings say “owner furnished”. | Owner | not stated | RRE installs / connects only | E2.0 |
SAFE-OFF EXISTING ELECTRICAL (TI) RRE carries the line; the read says “removal is by others”. | Others | not stated | RRE carries it; a part is by others | A101 |
DOUBLE DUPLEX (QUAD) RECEPTACLE 20A The drawings say “by gc”. | GC | not stated | RRE installs / connects only | E3.0 |
DATA OUTLET POSITION, WALL (video wall +85" AFF, storefront) The drawings say “by gc”. | GC | not stated | RRE installs / connects only | E3.0 |
TRACK, 3-CIRCUIT 120V SURFACE (Quattrobi XTS) Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | Owner | not stated | Struck: not in this bid | E2.0 |
16/2 CMR 0-10V DIMMING CABLE (TYPE B / BE 2x2 LED PANEL, LITHONIA CPX ...ZT 0-10V DRIVER), IN LIGHTING EMT Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | — | not stated | Struck: not in this bid | E1.0 |
CIRCUIT BREAKER 20A 1-POLE 120V BOLT-ON (PANEL L) Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | — | not stated | Struck: not in this bid | E4.1 |
CIRCUIT BREAKER 20A 1-POLE 277V BOLT-ON (PANEL H SPARES) Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | — | not stated | Struck: not in this bid | E4.1 |
GROUNDING ELECTRODE CONDUCTOR #6 CU BARE (XFMR SEPARATELY DERIVED SYSTEM) Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | — | not stated | Struck: not in this bid | E4.0 |
TEMPORARY POWER AND LIGHTING FOR CONSTRUCTION Struck by House rule (RRE lead estimator practice): Not in this bid: RRE’s lead estimator carries no temporary power (none on his last three estimates, and on earlier ones none even where the specs gave it to the EC). Put it back if this job needs it. | — | not stated | Struck: not in this bid | E5.0 |
CIRCUIT BREAKER 50A 3-POLE 480V BOLT-ON (PANEL H) Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | — | not stated | Struck: not in this bid | E4.1 |
CIRCUIT BREAKER 15A 3-POLE 208V BOLT-ON (PANEL L, EDH-1) Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | — | not stated | Struck: not in this bid | E4.1 |
BREAKER HANDLE TIE (PANEL L POS COUNTER L-6/8/10/12) Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | — | not stated | Struck: not in this bid | E4.1 |
TIE-IN AT EXISTING LANDLORD SWITCHBOARD 100A CB (EXISTING BREAKER, NO NEW GEAR) Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | — | not stated | Struck: not in this bid | E4.0 |
#6 BARE CU GROUNDING ELECTRODE CONDUCTOR - 30 KVA XFMR (SEPARATELY DERIVED) Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | — | not stated | Struck: not in this bid | E4.0 |
CIRCUIT BREAKER 50A 3P 480V BOLT-ON, 22 KAIC (PANEL H) Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | — | not stated | Struck: not in this bid | E4.1 |
CIRCUIT BREAKER 20A 1P 277V BOLT-ON, 22 KAIC (PANEL H, SPARE) Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | — | not stated | Struck: not in this bid | E4.1 |
CIRCUIT BREAKER 20A 1P 120/208V BOLT-ON, 10 KAIC (PANEL L) Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | — | not stated | Struck: not in this bid | E4.1 |
CIRCUIT BREAKER 15A 3P 208V BOLT-ON, 10 KAIC (PANEL L, EDH-1) Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | — | not stated | Struck: not in this bid | E4.1 |
BREAKER HANDLE TIE, 1P BOLT-ON (PANEL L POS COUNTER CKTS 6,8,10,12) Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | — | not stated | Struck: not in this bid | E4.1 |
TEMPORARY POWER AND LIGHTING FOR CONSTRUCTION (EC scope, spec 5.1g) Struck by House rule (RRE lead estimator practice): Not in this bid: RRE’s lead estimator carries no temporary power (none on his last three estimates, and on earlier ones none even where the specs gave it to the EC). Put it back if this job needs it. | — | not stated | Struck: not in this bid | E5.0 |
TEMPORARY POWER AND LIGHTING FOR CONSTRUCTION - tenant space #111, 1231 sf, from new Panel L / LL source Struck by House rule (RRE lead estimator practice): Not in this bid: RRE’s lead estimator carries no temporary power (none on his last three estimates, and on earlier ones none even where the specs gave it to the EC). Put it back if this job needs it. | — | not stated | Struck: not in this bid | A101 |
EQUIPMENT CONNECTION - VAV-1 Titus AESV VAV box, 120V 1-phase, factory control transformer and power fuse, above ceiling Struck by kelchlin: Not in this bid: answered on the drawing instead of a RRE Components item. | — | not stated | Struck: not in this bid | A101 |
| Nothing on this takeoff puts it in play. |
| 326 | Integrated Gas Spacer Cable: Type IGS | not in play | Nothing on this takeoff puts it in play. |
| 330 | Metal-Clad Cable: Type MC | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 332 | Mineral-Insulated, Metal-Sheathed Cable: Type MI | not in play | Nothing on this takeoff puts it in play. |
| 334 | Nonmetallic-Sheathed Cable: Types NM and NMC | not in play | Nothing on this takeoff puts it in play. |
| 335 | Instrumentation Tray Cable: Type ITC | not in play | Nothing on this takeoff puts it in play. |
| 336 | Power and Control Tray Cable: Type TC | not in play | Nothing on this takeoff puts it in play. |
| 337 | Type P Cable | not in play | Nothing on this takeoff puts it in play. |
| 338 | Service-Entrance Cable: Types SE and USE | not in play | Nothing on this takeoff puts it in play. |
| 340 | Underground Feeder and Branch-Circuit Cable: Type UF | not in play | Nothing on this takeoff puts it in play. |
| 342 | Intermediate Metal Conduit: Type IMC | not in play | Nothing on this takeoff puts it in play. |
| 344 | Rigid Metal Conduit: Type RMC | not in play | Nothing on this takeoff puts it in play. |
| 348 | Flexible Metal Conduit: Type FMC | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 350 | Liquidtight Flexible Metal Conduit: Type LFMC | not in play | Nothing on this takeoff puts it in play. |
| 352 | Rigid Polyvinyl Chloride Conduit: Type PVC | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 353 | High Density Polyethylene Conduit: Type HDPE Conduit | not in play | Nothing on this takeoff puts it in play. |
| 354 | Nonmetallic Underground Conduit with Conductors: Type NUCC | not in play | Nothing on this takeoff puts it in play. |
| 355 | Reinforced Thermosetting Resin Conduit: Type RTRC | not in play | Nothing on this takeoff puts it in play. |
| 356 | Liquidtight Flexible Nonmetallic Conduit: Type LFNC | not in play | Nothing on this takeoff puts it in play. |
| 358 | Electrical Metallic Tubing: Type EMT | checked | In play; none of its checked sections applies to these lines. |
| 360 | Flexible Metallic Tubing: Type FMT | not in play | Nothing on this takeoff puts it in play. |
| 362 | Electrical Nonmetallic Tubing: Type ENT | not in play | Nothing on this takeoff puts it in play. |
| 366 | Auxiliary Gutters | not in play | Nothing on this takeoff puts it in play. |
| 368 | Busways | not in play | Nothing on this takeoff puts it in play. |
| 369 | Insulated Bus Pipe (IBP)/Tubular Covered Conductors (TCC) Systems | not in play | Nothing on this takeoff puts it in play. |
| 370 | Cablebus | not in play | Nothing on this takeoff puts it in play. |
| 371 | Flexible Bus Systems | not in play | Nothing on this takeoff puts it in play. |
| 372 | Cellular Concrete Floor Raceways | not in play | Nothing on this takeoff puts it in play. |
| 374 | Cellular Metal Floor Raceways | not in play | Nothing on this takeoff puts it in play. |
| 376 | Metal Wireways | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 378 | Nonmetallic Wireways | not in play | Nothing on this takeoff puts it in play. |
| 380 | Multioutlet Assembly | not in play | Nothing on this takeoff puts it in play. |
| 382 | Nonmetallic Extensions | not in play | Nothing on this takeoff puts it in play. |
| 384 | Strut-Type Channel Raceway | not in play | Nothing on this takeoff puts it in play. |
| 386 | Surface Metal Raceways | not in play | Nothing on this takeoff puts it in play. |
| 388 | Surface Nonmetallic Raceways | not in play | Nothing on this takeoff puts it in play. |
| 390 | Underfloor Raceways | not in play | Nothing on this takeoff puts it in play. |
| 392 | Cable Trays | not in play | Nothing on this takeoff puts it in play. |
| 393 | Low-Voltage Suspended Ceiling Power Distribution Systems | not in play | Nothing on this takeoff puts it in play. |
| 394 | Concealed Knob-and-Tube Wiring | not in play | Nothing on this takeoff puts it in play. |
| 395 | Outdoor Overhead Conductors over 1000 Volts | not in play | Nothing on this takeoff puts it in play. |
| 396 | Messenger-Supported Wiring | not in play | Nothing on this takeoff puts it in play. |
| 398 | Open Wiring on Insulators | not in play | Nothing on this takeoff puts it in play. |
| checked |
| In play; none of its checked sections applies to these lines. |
| 425 | Fixed Resistance and Electrode Industrial Process Heating Equipment | not in play | Nothing on this takeoff puts it in play. |
| 426 | Fixed Outdoor Electric Deicing and Snow-Melting Equipment | not in play | Nothing on this takeoff puts it in play. |
| 427 | Fixed Electric Heating Equipment for Pipelines and Vessels | not in play | Nothing on this takeoff puts it in play. |
| 430 | Motors, Motor Circuits, and Controllers | checked | In play; none of its checked sections applies to these lines. |
| 440 | Air-Conditioning and Refrigerating Equipment | checked | In play; none of its checked sections applies to these lines. |
| 445 | Generators | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 450 | Transformers and Transformer Vaults (Including Secondary Ties) | checked | 1 section checked against the takeoff, all shown. |
| 455 | Phase Converters | not in play | Nothing on this takeoff puts it in play. |
| 460 | Capacitors | not in play | Nothing on this takeoff puts it in play. |
| 470 | Resistors and Reactors | not in play | Nothing on this takeoff puts it in play. |
| 480 | Stationary Standby Batteries | not in play | Nothing on this takeoff puts it in play. |
| 490 | Equipment Over 1000 Volts, Nominal | not in play | Nothing on this takeoff puts it in play. |
| Nothing on this takeoff puts it in play. |
| 514 | Motor Fuel Dispensing Facilities | not in play | Nothing on this takeoff puts it in play. |
| 515 | Bulk Storage Plants | not in play | Nothing on this takeoff puts it in play. |
| 516 | Spray Application, Dipping, Coating, and Printing Processes | not in play | Nothing on this takeoff puts it in play. |
| 517 | Health Care Facilities | not in play | Nothing on this takeoff puts it in play. |
| 518 | Assembly Occupancies | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 520 | Theaters, Audience Areas of Motion Picture and Television Studios, Performance Areas, and Similar Locations | not in play | Nothing on this takeoff puts it in play. |
| 522 | Control Systems for Permanent Amusement Attractions | not in play | Nothing on this takeoff puts it in play. |
| 525 | Carnivals, Circuses, Fairs, and Similar Events | not in play | Nothing on this takeoff puts it in play. |
| 530 | Motion Picture and Television Studios and Similar Locations | not in play | Nothing on this takeoff puts it in play. |
| 540 | Motion Picture Projection Rooms | not in play | Nothing on this takeoff puts it in play. |
| 545 | Manufactured Buildings and Relocatable Structures | not in play | Nothing on this takeoff puts it in play. |
| 547 | Agricultural Buildings | not in play | Nothing on this takeoff puts it in play. |
| 550 | Mobile Homes, Manufactured Homes, and Mobile Home Parks | not in play | Nothing on this takeoff puts it in play. |
| 551 | Recreational Vehicles and Recreational Vehicle Parks | not in play | Nothing on this takeoff puts it in play. |
| 552 | Park Trailers | not in play | Nothing on this takeoff puts it in play. |
| 555 | Marinas, Boatyards, Floating Buildings, and Commercial and Noncommercial Docking Facilities | not in play | Nothing on this takeoff puts it in play. |
| 590 | Temporary Installations | not in play | Nothing on this takeoff puts it in play. |
| Nothing on this takeoff puts it in play. |
| 646 | Modular Data Centers | not in play | Nothing on this takeoff puts it in play. |
| 647 | Sensitive Electronic Equipment | not in play | Nothing on this takeoff puts it in play. |
| 650 | Pipe Organs | not in play | Nothing on this takeoff puts it in play. |
| 660 | X-Ray Equipment | not in play | Nothing on this takeoff puts it in play. |
| 665 | Induction and Dielectric Heating Equipment | not in play | Nothing on this takeoff puts it in play. |
| 668 | Electrolytic Cells | not in play | Nothing on this takeoff puts it in play. |
| 669 | Electroplating | not in play | Nothing on this takeoff puts it in play. |
| 670 | Industrial Machinery | not in play | Nothing on this takeoff puts it in play. |
| 675 | Electrically Driven or Controlled Irrigation Machines | not in play | Nothing on this takeoff puts it in play. |
| 680 | Swimming Pools, Fountains, and Similar Installations | not in play | Nothing on this takeoff puts it in play. |
| 682 | Natural and Artificially Made Bodies of Water | not in play | Nothing on this takeoff puts it in play. |
| 685 | Integrated Electrical Systems | not in play | Nothing on this takeoff puts it in play. |
| 690 | Solar Photovoltaic (PV) Systems | not in play | Nothing on this takeoff puts it in play. |
| 691 | Large-Scale Photovoltaic (PV) Electric Supply Stations | not in play | Nothing on this takeoff puts it in play. |
| 692 | Fuel Cell Systems | not in play | Nothing on this takeoff puts it in play. |
| 694 | Wind Electric Systems | not in play | Nothing on this takeoff puts it in play. |
| 695 | Fire Pumps | not in play | Nothing on this takeoff puts it in play. |
| not in play |
| Nothing on this takeoff puts it in play. |
| 725 | Class 1, Class 2, and Class 3 Remote-Control, Signaling, and Power-Limited Circuits | not read yet | In play. This job’s read has no code pass yet: re-run the read, or check it on the drawings. |
| 726 | Class 4 (CL4) Fault-Managed Power Systems | not in play | Nothing on this takeoff puts it in play. |
| 728 | Fire-Resistive Cable Systems | not in play | Nothing on this takeoff puts it in play. |
| 750 | Energy Management Systems | not in play | Nothing on this takeoff puts it in play. |
| 760 | Fire Alarm Systems | not in play | Nothing on this takeoff puts it in play. |
| 770 | Optical Fiber Cables | not in play | Nothing on this takeoff puts it in play. |
RRE