Takeoff — review the count

Summed 8 dimensioned LAL runs printed on the plan: LAL01 16'-8", LAL02 16'-8", LAL03 15'-0", LAL04 15'-0", LAL5 29'-8", LAL6 48'-3", LAL7 56'-5", LAL8 60'-9" = 258.42 ft. Matches job-facts.md Table F's LAL parenthetical of 256.6 within 0.7% -- strong confirmation that Table F's LAL number is total feet, not a luminaire count. Billed in FEET per SKILL.md v2.2. STEP 4.5 TOP-5 LABOR RE-DERIVATION: 258.42 ft was re-checked against A-130's independent measurement of the same LAL run (230.7 ft, L-0093) - the two disagree by ~11%, flagged on this line. Re-measuring from the extracted vector geometry (not re-reading the whole sheet) confirms the E-300 dimension_measurement method is internally consistent with the run segments recorded in job-facts.md; the gap to A-130 is carried as a reconciliation item, not silently averaged. (Model line id L-0019.) The model also raised "cross-sheet check (Step 4.5): A-130 RCP independently read this family as 230.7 vs this line's 258.42 (L-0093); E-300 plan count used per policy, reconcile before bid", 'Step 4.5 top-5-labor re-derivation: see updated narrative', which the contract has no flag for; recorded here rather than dropped.

Summed 9 dimensioned LAF runs printed directly on the plan: LAF1-7 (mirror strips) at 16'-4" each = 114'-4", plus LAF8 18'-5" and LAF9(comitted) 7'-3" = 140.0 ft total. This total lands within 0.9% of job-facts.md Table F's LAF parenthetical of 141.2 (read there as total feet, not luminaire count, given this close a match), confirming these 9 runs are the LAF family and that LAF10/LAF10a (billed separately below) are the distinct 'LAF10 Storefront Lighting' schedule row. Billed in FEET per SKILL.md v2.2 (linear/strip fixtures priced by the foot, not per run). STEP 4.5 TOP-5 LABOR RE-DERIVATION: 140.0 ft cross-checked against A-130's independent read of the same LAF run (L-0094, also 140.0 ft) - exact agreement between two different sheets/methods. This line's footage is confirmed, not just modelled. (Model line id L-0017.) The model also raised 'Step 4.5 top-5-labor re-derivation: see updated narrative', which the contract has no flag for; recorded here rather than dropped.

Text-search hits: 94 upright 'P15.1W' + 21 additional hits read as 'P15.1b' (the rotated/vertical placements of the same tag along diagonal Track 2 runs, where PDF text extraction misreads the rotated 'W' glyph) = 109... corrected to 115 by summing both literal strings (94+21=115), which matches job-facts Table F count for P15.1w exactly (115). Confirmed by visual spot-check on crops/topmid.png and crops/midright.png that 'P15.1b' labels sit on rotated copies of the same track-head block as 'P15.1W'. STEP 4.5 TOP-5 LABOR RE-DERIVATION: re-derived by summing A-130's independent tag read (L-0076 P15.1W=94 + L-0077 P15.1b=21 = 115) against this line's single plan-tag count of 115 - exact match once the P15.1b rotated-tag reads are folded in, which confirms the existing flag's hypothesis (P15.1b hits are rotated P15.1W reads) rather than a distinct fixture type. Quantity 115 stands, confidence held at B pending a straight visual tally. (Model line id L-0009.) The model also raised "confirm the 21 'P15.1b' hits are rotated P15.1W reads, not a distinct tag, on the next pass", 'Step 4.5 top-5-labor re-derivation: see updated narrative', which the contract has no flag for; recorded here rather than dropped.

Counted every 'P08.1W' text tag on E-300 via exact word-search on the live PDF text layer (95 hits, page-wide, deduplicated) -- these sit beside the small rectangular track-head marks drawn along TRACK 1, 3, 5 and 7. Matches job-facts.md Table F count for P08.1w exactly (95), so all 95 schedule luminaires of this type live on this sheet. Track heads are billed per-head; track-length footage (8'/4' sections) was NOT separately measured this pass -- see coverage_gaps. STEP 4.5 TOP-5 LABOR RE-DERIVATION: cross-checked against A-130's independent tag read of the same family (L-0075, 95) - exact match. Two sheets, two agents, same count; quantity 95 confirmed, band raised to A on this evidence. (Model line id L-0008.) The model also raised 'Step 4.5 top-5-labor re-derivation: see updated narrative', which the contract has no flag for; recorded here rather than dropped.

28 'E06W' text tags counted on E-300 (exact word-search, page-wide). Matches job-facts.md Table F count for E06W exactly (28) -- all schedule luminaires of this type are on this sheet, drawn as the small pendant/drop-style icon along the 'LAF 9' strip and storefront run. (Model line id L-0010.)

Two dimensioned runs tagged 'LAF10: 13'-8"' and 'LAF10a: 13'-8"' sum to 27'-4" (27.33 ft). job-facts.md Table F lists 'LAF10 Storefront Lighting' as a separate schedule row from generic LAF (count 28 luminaires) -- billed here in feet per policy since it is a strip/linear fixture, not per-luminaire. (Model line id L-0018.) The model also raised 'Table F bills LAF10 by luminaire count (28); this line bills the same tag by measured feet (27.33 ft) per the linear-fixture-in-feet policy -- reconcile units before pricing', which the contract has no flag for; recorded here rather than dropped.

25 'E12.1W' text tags counted on E-300. job-facts.md Table F lists E12.1w(26) -- one short. Per SKILL.md v2.2 policy the PLAN COUNT governs the line quantity; the schedule is the cross-check. Flagging the 1-unit disagreement rather than silently reconciling to the schedule number -- the missing unit may be a duplicate/overlapping glyph the word-search folded into an adjacent tag, or may genuinely live on E-400. (Model line id L-0011.) The model also raised 'plan count (25) vs Table F schedule count (26) disagree by 1 -- flagged per policy, plan count used', which the contract has no flag for; recorded here rather than dropped.

Each of the 3 Point-of-Sale plan symbols shows '(6) DATA LINES (CAT 6A)' per the A-120 legend; 3 positions x 6 lines = 18. Cable spec and punch-down slack note per legend's 'Data Line' row (RJ45/Cat 6A/plenum rated, min 6' left for punch-down). (Model line id L-0071.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Counted 14 standalone 'EM5' tags across the full sheet (200-dpi render, 6 non-overlapping tiles) -- the most frequent of the three, scattered through the fitting-room area and the open sales floor. Same unresolved-meaning caveat as EM2/EM3 above -- no legend on this sheet. This is the largest-quantity line on this sheet and carries the most dollar risk if it turns out to double-count fixtures already priced on E-300/E-400. (Model line id L-0059.) The model also raised 'UNSURE whether this is new EC scope or an option flag on an already-counted fixture -- see coverage_gaps', 'no legend on this sheet defines the EM+digit convention', 'highest-quantity line on this sheet -- priority for reconciliation against E-300/E-400', which the contract has no flag for; recorded here rather than dropped.

Note 26-12.22a mandates conduit feed to the cash-counter outlet with exposed conduit painted to match; no homerun tag, panel location, or dimensioned conduit run appears anywhere on this millwork sheet (it has no power plan). Per house policy (stub_assembly_rule, v1.9), a 12-ft jbox+stub allowance is carried at every device connection point until the E-series power plan or riser gives an actual run length. Striking this line would carry the outlet in L-0001 with zero raceway, which understates scope. (Model line id L-0114.) The model also raised 'modelled_allowance', 'no_measurable_footage_on_this_sheet', 'verify_against_E-series_power_plan_or_riser', which the contract has no flag for; recorded here rather than dropped.

11 'E10.1W' text tags counted on E-300 (exterior recessed cans tagged '10,k' along the storefront/canopy edge). This exact tag does NOT appear anywhere in job-facts.md's Table F fixture schedule (which runs E11.1W, E12.1W, E06W, E05W but has no E10.1W row) -- either Table F has an omitted row, or E10.1W is a legend-only variant this pass could not settle against a schedule. assembly_id withheld pending schedule reconciliation. (Model line id L-0014.) The model also raised 'fixture tag E10.1W has no Table F schedule entry -- confirm against E-800/E-801 Table F for a missed row before pricing', which the contract has no flag for; recorded here rather than dropped.

11 'BA' text tags counted on E-300 (back-of-house aisle fixtures tagged '11,f', drawn as a circle-with-X suspended-fixture icon). job-facts.md Table F lists BA(13) -- 2 short of the schedule total. One tag ('BA/EM') was seen combined with an emergency designator and may already be one of the 11 counted rather than an additional unit; the remaining 2-unit gap may sit on E-400. Flagged rather than padded to 13. (Model line id L-0015.) The model also raised 'plan count (11) vs Table F schedule count (13) disagree by 2 -- flagged, plan count used per policy; check E-400 for the remainder', "cross-sheet check (Step 4.5): A-130 RCP independently read this family as 13 vs this line's 11 (L-0079); E-300 plan count used per policy, reconcile before bid", which the contract has no flag for; recorded here rather than dropped.

Counted 11 standalone 'EM2' tags across the full sheet (200-dpi render, 6 non-overlapping tiles: 3 in the fitting-rooms/office quadrant, 2 in the storefront diagonal bump-out, 3 near the stockroom, 3 near sales-floor perimeter). No legend or keyed note on A-092 (or in this run's read set) defines what the digit '2' means -- possibly a remote emergency-head wattage/model class distinct from the numbered EM3/EM5 tags, possibly a battery-pack VA rating on an unlabelled main fixture. Carried as its own line rather than merged with EM3/EM5 because the tag text is visibly distinct on the sheet; see coverage_gaps for the double-count risk against E-300/E-400. (Model line id L-0057.) The model also raised 'UNSURE whether this is new EC scope (remote emergency head + wiring) or an option flag on an already-counted E-300/E-400 fixture -- see coverage_gaps', 'no legend on this sheet defines the EM+digit convention', which the contract has no flag for; recorded here rather than dropped.

9 'E05W' text tags counted on E-300 (fitting-room recessed cans tagged '9,e'). job-facts.md already flagged this exact tag/schedule disagreement: the Table F tag suffix reads 'E05W(9)' but the Table F Total-Number-of-Luminaires column reads 8. This sheet's plan count (9) agrees with the tag-suffix reading, not the column-07 count -- per SKILL.md's plan-count-governs rule this line carries 9, with the schedule's 8 flagged as the disagreement to resolve. (Model line id L-0013.) The model also raised "plan count (9) vs Table F 'Total Number of Luminaires' column (8) disagree -- flagged in job-facts.md, plan count used per policy", which the contract has no flag for; recorded here rather than dropped.

Text layer of A-150 (decoded custom glyph encoding, +29 shift) contains exactly 8 in-plan instances of the word 'WIFI' (ellipse device tag, legend-column instances excluded by x-position < 620pt). Visual zoom crops directly confirmed 6 of the 8 numbered tags: AP-001 (near the storefront/rack wall, top of sales floor), AP-002 (mid sales floor), AP-004 (near the fitting-room row), AP-005 (rear storage aisle), AP-006 (QA/office area), AP-007 (center of sales floor). Per general note 1 on this sheet ('EACH DEVICE A HOME RUN') and note 5 (LAN switch/router lives in the stockroom rack), each of the 8 access points gets its own Cat 6A home run to the rack; general notes 2-3 assign the actual wire pull to GC (=EC per the house default and the A-090 Div 27 matrix, which flagged its own AP-cabling schedule row as needing this sheet's instance count). Striking this line drops the AP cabling multiplier back to A-090's uncounted placeholder of 1. (Model line id L-0096.) The model also raised 'no_priced_assembly', 'resolves_A-090_L-0001_multiplier', which the contract has no flag for; recorded here rather than dropped.

6 'E11.1W' text tags counted on E-300 (aisle recessed cans tagged '7,d'). Matches job-facts.md Table F count for E11.1w exactly (6). (Model line id L-0012.)

6 'EX1' text tags counted on E-300 (small square ceiling-mount exit-sign symbol). Matches job-facts.md Table F count for EX01 exactly (6). A second, visually distinct bold black bar-shaped exit/emergency symbol repeatedly labelled '41/EX' also appears on this sheet, but that label is a CAD block with curve-drawn text (0 hits in the PDF text layer for 'EX' outside the 'EX1'/'EXT.'/'EXISTING' words already accounted for) and was not exhaustively tallied within this pass's time budget -- see coverage_gaps. EX02(1) from Table F was not identified as a distinct symbol on this sheet either. (Model line id L-0016.) The model also raised "EX02 (schedule qty 1) and the black-bar '41/EX' wall-mount exit/emergency symbol were not reconciled to a count this pass -- see coverage_gaps", which the contract has no flag for; recorded here rather than dropped.

Equipment Schedule IT Rack row: Low Voltage cabling column '(6) Cat 6A', 4' length, keyed note 2. Explicit count of 6. (Model line id L-0034.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Counted 5 standalone 'EM3' tags across the full sheet (200-dpi render, 6 non-overlapping tiles), clustered around the stockroom/restroom/back-of-house area. Same unresolved-meaning caveat as EM2 above -- no legend on this sheet. (Model line id L-0058.) The model also raised 'UNSURE whether this is new EC scope or an option flag on an already-counted fixture -- see coverage_gaps', 'no legend on this sheet defines the EM+digit convention', which the contract has no flag for; recorded here rather than dropped.

Counted 4 'P01W' text spans on the A-130 RCP, each adjacent to a stand-alone 'S' text tag. No 'P01W' row exists in the E-800 Title-24 Table F schedule captured in job-facts.md. Counted and carried with assembly_id null pending schedule/legend confirmation. (Model line id L-0087.) The model also raised '{\'code\': \'no_schedule_match\', \'note\': "P01W not found in the read E-800 fixture schedule. Adjacent \'S\' tag suggests a switch or spot designation -- confirm against E-300/E-400 or a cutsheet."}', which the contract has no flag for; recorded here rather than dropped.

Counted 4 'P02W' text spans on the A-130 RCP, each adjacent to a stand-alone 'F' text tag. No 'P02W' row exists in the E-800 Title-24 Table F schedule captured in job-facts.md. Counted and carried with assembly_id null pending schedule/legend confirmation. (Model line id L-0088.) The model also raised '{\'code\': \'no_schedule_match\', \'note\': "P02W not found in the read E-800 fixture schedule. Adjacent \'F\' tag suggests a fixed or flood designation -- confirm against E-300/E-400 or a cutsheet."}', which the contract has no flag for; recorded here rather than dropped.

Counted 3 'BA EM' red text tags across a full-sheet visual sweep of A-092 (200-dpi render, 6 non-overlapping tiles, no double-count risk). This ties to the same 'BA' suspended-4' fixture family the E-300 sheet agent counted (11 of a Table F total of 13) -- these 3 units are the ones this job's designer flagged for the emergency battery-pack option on the photometric plan. Striking this line drops the only record on this run of which BA fixtures carry emergency power; it does NOT add new fixture bodies (those are already counted on E-300). (Model line id L-0055.) The model also raised 'cross-check against E-300/E-400 BA count -- this is the EM subset of that same family, not an addition to it', which the contract has no flag for; recorded here rather than dropped.

Counted 3 'Point of Sales' legend symbols along the cash-wrap millwork run (labelled EQ-1a/EQ-1d in plan, matching A-090 Equipment Schedule POS Station rows), one per millwork bay. A-120 Power & Low Voltage legend defines this symbol as '(1) QUADRUPLEX WHITE'. This plan count settles the A-090 coverage gap that carried POS as 1 unverified instance - actual count is 3. (Model line id L-0070.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Counted 3 'Cash Counter' legend symbols, one per cash-wrap millwork bay, adjacent to but distinct from the Point-of-Sale symbol in the same bay (legend: Cash Counter = '(1) QUADRUPLEX/WHITE', no data lines). Matches A-090's separate 'POS Station Power' schedule rows describing a white quad plus a dedicated-breaker red quad per counter - this sheet's plan symbol does not distinguish white vs red quad, carried here as 1 general quad per counter position pending A-090 cross-check for the dedicated-circuit variant. (Model line id L-0072.) The model also raised 'no_priced_assembly', 'variant_needs_A-090_cross_check', which the contract has no flag for; recorded here rather than dropped.

Visually located 3 instances of the 'CLK / 54"AFF' hardwire symbol across the plan (near the BOH/kitchenette corridor, at the storefront entry facade, and along a mid-floor demising wall). Legend explicitly defines this symbol as hardwire power for illuminated mirrors. Exact mirror locations/count not cross-checked against interior elevations - see coverage_gaps. (Model line id L-0073.) The model also raised 'no_priced_assembly', 'location_purpose_unconfirmed', 'quantity_needs_full_symbol_scan', which the contract has no flag for; recorded here rather than dropped.

Counted 3 'BA/EM' text spans on the A-130 RCP, in addition to the 13 plain 'BA' tags (L-0005). The E-800 schedule totals BA at 13 with no separate emergency-variant line, so the plan's total of 16 BA-family fixtures (13+3) disagrees with the schedule's 13. Per SKILL.md plan_count_governs_fixture_lines, the plan count (3, additive to L-0005) is carried; the disagreement is flagged rather than resolved. (Model line id L-0080.) The model also raised "{'code': 'plan_schedule_disagreement', 'note': 'Schedule (E-800 Table F) shows BA(13) total; plan shows 13 plain BA + 3 BA/EM = 16. Confirm whether BA/EM are additional fixtures or a re-tag of 3 of the 13 onto the emergency circuit (Panel A ckt 41, lock-on breaker per E-601 keyed note).'}", which the contract has no flag for; recorded here rather than dropped.

Mall Note 11 states 'INTERLOCK EXHAUST FAN WITH BATHROOM LIGHT SWITCHES.' This mandates a control/wiring task at each restroom light switch (tie the fan's neutral/switch-leg to the same switch as the light, or add a relay), which normally falls to the EC. Quantity of 2 is inferred from this sheet's own Scope of Work line 'EXISTING OFFICE AND BOTH RESTROOMS TO BE REUSED' (2 restrooms), not from a plan count - no restroom plan or fan schedule was in this agent's read set. Striking this line would drop the only interlock-wiring requirement found on this sheet. Quantity is inferred, not counted; verify against A-005/A-006 and the M-set exhaust fan schedule. (Model line id L-0022.) The model also raised 'no_priced_assembly', 'quantity_inferred_verify_restroom_count', 'cross_check_mechanical_fan_schedule', which the contract has no flag for; recorded here rather than dropped.

General note item 3 in the description block and the 'UPPER LED WHEN CEILING IS>13'-0"' callout on detail 4 both describe a second LED run added above the base run, conditional on ceiling height exceeding 13'-0", and both say 'Refer to Lighting plan' for where it applies. Quantity of 2 is carried paired with the 2 base-run instances in L-0001 (one possible upper run per panel type documented on this sheet), but this sheet gives no ceiling heights by location, so whether this condition is ever triggered on the actual job cannot be confirmed here - flagged UNSURE and carried as a conditional allowance rather than dropped, since striking it silently would hide a real scope trigger from whoever prices the lighting plan. (Model line id L-0028.) The model also raised 'no_priced_assembly', 'conditional_on_ceiling_height_not_shown_on_this_sheet', 'verify_against_E-300_lighting_plan_or_RCP_ceiling_heights', 'owner_furnished_fixture_ec_install_labor_only', which the contract has no flag for; recorded here rather than dropped.

Detail 2 elevation view explicitly calls out 'PROVIDE TWO QUAD POWER OUTLETS @ 36" AFF. ON CENTER' with two 4-opening receptacle symbols drawn side by side inside the shelf-unit outline; the same count and mounting height are repeated in text under both furnish options (a) and (b) ('Power outlets mounted @ 36" AFF between the top and bottom shelf'). Both the drawn symbol count (2) and the note text ('TWO') agree. Striking this line drops the only EC device scope this detail sheet carries. (Model line id L-0030.) The model also raised 'assembly_id_null_needs_catalog_entry_quad_receptacle', 'reconcile_with_panel_A_ckt32_charging_station_recorded_on_E-601', 'homerun_conduit_wire_to_this_device_not_on_this_sheet_see_coverage_gaps', 'grommet_furnish_responsibility_UNSURE_see_coverage_gaps', which the contract has no flag for; recorded here rather than dropped.

Equipment Schedule EQ-12 'Camera' (Mini-Dome Camera, Retail): '(1) Cat 6A', keyed note 2, 2MP Varifocal IP; 'Camera Screen' (Office): '(1) Cat 6A', keyed note 2. Two Cat 6A drops total. Matrix confirms 'SECURITY CAMERAS WIRING' is G.C.(EC) supply+install while the cameras themselves are Mango supply+install. (Model line id L-0037.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Equipment Schedule EQ-17a 'Power Pack' AMS-9060, Entry Door: '(1) Duplex 110V'; EQ-17h 'CapBox', Sensomatic, Sales Area: '(1) Duplex 110V', comment 'GC to coordinate power as necessary'. Two duplex receptacles. (Model line id L-0041.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Equipment Schedule EQ-20 Invonics rows: two rows list Low Voltage cabling '4/18awg' with comment 'GC provide and install all wiring' (door opener, door release). (Model line id L-0044.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Equipment Schedule EQ-30a/EQ-30b 'Sign - Illuminated', Mango(owner) provider, GC installer, Entrance location, power '110 V' each, keyed note 10. Matches responsibility matrix 'CONNECTION OF SIGNAGE BOXES' = G.C.(EC) supply+install. (Model line id L-0046.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Equipment Schedule rows 'Speaker on track' (Owner device, GC wire, '16/2 (V-...' Voltive V-1215, plenum rated wire, keyed note 7) and 'Surface Speakers' (Owner device, Owner install, GC wire, Voltive V-1215 plenum rated). Two 16/2 wire runs, Sales Area. (Model line id L-0049.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Counted the text tag 'APPROXIMATE TRENCHING LOCATION' (decoded from the sheet's shifted encoding) on the A-110 plan (detail 1): two distinct rotated call-outs, at page-point centroids approximately (1133, 1160) and (1401, 935), each with a leader to a hatched trench zone. Keyed note 02-42.53 assigns the trenching conduit burial (both low- and line-voltage) as EC/Division 26-28 raceway scope, coordinated with the GC and landlord for the cut. Two locations counted -- see marks/A-110.json. (Model line id L-0067.) The model also raised 'no_dimensioned_length_this_sheet', 'no_assembly_match', which the contract has no flag for; recorded here rather than dropped.

E-601 panel schedule block titled 'NEW CURRENT LIMITING PANEL CL' - 20 poles, 120V, 1Ø/2W, service FEED-THRU, mounting SURFACE, location 'GR 2400 THE SILVERBULLET'. Confirmed as the only NEW gear on this job by the E-600 riser, which shows MSB-South, Panel MB, the 45kVA transformer, Panel A and Panel B all drawn dashed/labelled EXISTING, while CL is the one box fed by a labelled feeder terminating in new equipment. Striking this line removes the only new panel on the job. (Model line id L-0001.)

E-600 riser shows a feeder labelled 'EXISTING 4#4 & 1#8 GND. IN 1-1/4" C.' running from the existing 45kVA transformer secondary to the new Current Limiting Panel box. The conduit/conductor run itself is drawn dashed (existing-to-remain per the sheet legend) so no new raceway or wire is taken off for it here; the only EC work this line captures is the physical termination of those existing conductors onto the new panel's lugs/bus, which is unavoidable new labor regardless of the conduit's age. See coverage_gaps for the risk that this feeder is not actually pre-existing at this exact run. (Model line id L-0003.) The model also raised 'UNSURE - confirm the feeder is truly an existing/reused run and not new conduit+wire mislabelled', which the contract has no flag for; recorded here rather than dropped.

House standard mandates a disconnect at every tenant-wired electric water heater (knowledge/estimators/house.json gear_musts) regardless of whether the schedule shows one explicitly; the EWH circuit itself is read directly off Panel B ckt7/9. This is the house policy line, not a drawn disconnect - it has caused a real miss (NUYO blind #5) when omitted. (Model line id L-0007.)

One 'HUB' tag found on E-300 at the back-of-house wall, with keyed note '#38 (LUTRON VIVE HUB) 2#12 & 1#12 GND. IN 3/4" C.' and a leader to 'LUTRON VIVE SYSTEM: CENTRAL HUB, SEE WIRING DIAGRAM... SEE LIGHTING KEY NOTE 4.' Controls hardware is vendor-quote/labor-only per house default (Lutron via Thea Enterprises, per job-facts.md) -- carried here as a countable device with assembly pending vendor quote. (Model line id L-0020.) The model also raised 'controls hardware furnished-by is UNSURE per job-facts.md (no cover sheet this run) -- hub itself may be vendor-supplied, EC installs', which the contract has no flag for; recorded here rather than dropped.

Cover-sheet Electrical note 30.a states 'TENANT TO INSTALL AN ELECTRIC METER FOR THE MAIN ELECTRICAL SYSTEM. SHOULD BE EITHER QUADLOGIC RSM5 OR S20 METER.' Note 30.b immediately follows with 'FINAL CONNECTION OF TENANTS ELECTRICAL SERVICE SHALL BE BY THE LL CONSTRACTOR,' meaning the EC/tenant sets the meter but the landlord's contractor makes the final service tie-in. No meter location, socket type, or CT-cabinet detail is drawn on this cover sheet; this is a single note-driven allowance, one meter, until the riser (E-600) or A-090 responsibility matrix confirms it. Striking this line would drop the only meter-install item found in this read set. (Model line id L-0021.) The model also raised 'no_priced_assembly', 'unsure_furnish_vs_install', 'verify_against_E-600_riser_and_A-090_matrix', which the contract has no flag for; recorded here rather than dropped.

Read keyed note 06-22.30 'Mirror Panel', item g: 'Provide clock outlet.' This is a millwork/architectural detail sheet (Cortland Morgan Architect A-set), not an E-sheet, but the note mandates a device (a recessed power outlet for a wall clock behind the mirror) that is Division 26/EC scope -- per this run's ec_scope_on_other_disciplines process, EC-scope items found on non-electrical sheets are still taken off. Counted as 1 per the single mirror-panel detail shown on this sheet; the true building-wide count depends on how many fitting-room mirrors of this type exist, which is not shown here (see coverage_gaps). (Model line id L-0024.) The model also raised 'cross_discipline_source_sheet', 'quantity_multiplier_unresolved_pending_floor_plan', 'no_assembly_match', which the contract has no flag for; recorded here rather than dropped.

Equipment Schedule row 'AP-# WiFi Cabling': Owner-provider, G.C. installer, '(1) Cat 6A', 4' length, keyed note 2 'Each a home run to the rack'. Counted as 1 instance; actual AP count is on the power/LV plan, not this schedule. (Model line id L-0031.) The model also raised 'no_priced_assembly', 'quantity_needs_plan_count', which the contract has no flag for; recorded here rather than dropped.

Equipment Schedule EQ-2b 'Speaker Control Relay': GC provider and installer, model RDL Stick-on Series, IT Rack. Comment: 'GC to provide and install relay. Relay to shut in store music off when Fire alam or building alarm is activated. Coordinate with LL.' (Model line id L-0035.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Equipment Schedule 'Camera Screen' row, model K5A38AA#ABA, Office: power column '(1) Duplex 110V', keyed note 2. (Model line id L-0036.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Equipment Schedule EQ-14 'Refrigerator', Frigidair FFPE3322UM, SS finish, Kitchenette, power '110 V', comment 'GC provided and installed'. (Model line id L-0038.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Equipment Schedule EQ-15 'Microwave', Frigidaire FFCM0934LS, SS finish, Kitchenette, power 'Dedicated 110 V', comment 'GC provided and installed'. (Model line id L-0039.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Equipment Schedule EQ-17b 'Security Antennas', Sensormatic Concealed, Entry Door: keyed note 5A 'Provide 3/4" conduit below finish floor'. Counted as 1 pedestal location; number of entry doors carrying this device not given on this sheet. (Model line id L-0040.) The model also raised 'no_priced_assembly', 'quantity_needs_plan_count', which the contract has no flag for; recorded here rather than dropped.

Equipment Schedule row 'Façade Flag Sign', GC installer, Façade location, power '110 V', comment 'GC to permit and Install - Ensure that signage is on a timer clock.' Ties to job-facts Sub-Panel B ckt1 SIGNAGE controlled via Lutron Vive time clock (E-900). (Model line id L-0047.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Equipment Schedule EQ-38B 'Blade: Illuminated', GC provider AND installer (unlike the other sign rows, which are Owner-provided/GC-installed only). (Model line id L-0048.) The model also raised 'no_priced_assembly', 'furnish_scope_unusual_confirm', which the contract has no flag for; recorded here rather than dropped.

Equipment Schedule 'Subwoofer' row, Ecler Trail SB6T, White, Sales Area, low voltage '14/2 (V-...', 4' length, keyed note 8. (Model line id L-0050.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Responsibility Matrix Div 26 row 'LINE WIRE CONNECTION & WIRING OF CASHWRAP': G.C. Supply = X, G.C. Install = X. No length/count given on this sheet; carried as 1 allowance item pending cross-check against the power/telecom plan. (Model line id L-0051.) The model also raised 'no_priced_assembly', 'quantity_needs_plan_count', which the contract has no flag for; recorded here rather than dropped.

Responsibility Matrix Div 27 row 'LOW VOLTAGE DATA PUNCH DOWN': only G.C. Install = X marked (no supply column marked). Carried as 1 allowance item; drop count not given on this sheet. (Model line id L-0052.) The model also raised 'no_priced_assembly', 'quantity_needs_plan_count', which the contract has no flag for; recorded here rather than dropped.

Responsibility Matrix Div 27 rows 'ENTRY DOOR LOOP PRE INSTALLATION COORDINATION' (comment: Sensomatic site survey) and 'ENTRY DOOR LOOP TRENCHING' (comment: Coordinate w/Sensomatic): both G.C. Supply = X, G.C. Install = X. No trench length given on this sheet. (Model line id L-0053.) The model also raised 'no_priced_assembly', 'quantity_needs_plan_count', which the contract has no flag for; recorded here rather than dropped.

Responsibility Matrix Div 27 rows 'LOW VOLTAGE FROM MAIN UTILITY CLOSET TO RETAIL SPACE' and 'CONDUIT FOR ALL LOW VOLTAGE WIRING': both G.C. Supply = X, G.C. Install = X. No route length given on this sheet - the LV/telecom riser plan (A-150, not in this agent's assigned pages per SKILL.md v2.2 note) would carry the footage. (Model line id L-0054.) The model also raised 'no_priced_assembly', 'quantity_needs_plan_count', 'needs_A-150', which the contract has no flag for; recorded here rather than dropped.

One 'QA EM' red text tag found near the stockroom/restroom corridor on A-092. 'QA' does not match any of the 13 fixture types in job-facts.md's Table F (BA, E12.1W, E06W, S02, E05W, E11.1W, LAL, LAF, P08.1w, P15.1w, EX01, EX02, LAF10) -- either an uncatalogued fixture type this run's schedule pages missed, or a mislabel. assembly_id withheld until reconciled. (Model line id L-0056.) The model also raised "fixture family 'QA' has no matching Table F row -- confirm against E-800 pp.1-6 or E-400 before pricing", 'semantic risk: name read from the sheet with no legend/schedule confirmation', which the contract has no flag for; recorded here rather than dropped.

Read keyed note 02-42.52 ('Sensormatic slab scribe'). This is EC/low-voltage scope per house default (LV cabling/raceway = EC pulls, raceway by EC) even though the note is written under the GC-coordinated demolition/slab-work section -- the conduit itself and its antenna-to-wall/ceiling run are electrical material and labor. No footage or antenna-pedestal count is shown on A-110; carried as a lump-sum system allowance pending the security/EAS equipment plan. (Model line id L-0066.) The model also raised 'lump_sum_no_plan_quantity', 'lv_responsibility_unsure_per_job_facts', 'no_assembly_match', which the contract has no flag for; recorded here rather than dropped.

Read keyed note 02-42.60 ('Slab Core Drill'): low voltage and line voltage must be in separate conduits through each core-drilled penetration; conduit sizing is GC-coordinated but the conduit itself is EC material/labor. No specific penetration count or location is shown on A-110 -- carried as a lump-sum coordination/material allowance. (Model line id L-0068.) The model also raised 'lump_sum_no_plan_quantity', 'no_assembly_match', which the contract has no flag for; recorded here rather than dropped.

A-120 labels one location 'CHARGING STATION' in plan, adjacent to the kitchenette sink/hot-water-heater (FX-4/FX-20). This ties to job-facts Panel A's revision-clouded new circuit block (ckt32/34/36/38/40/42) which includes a 'CHARGING STATION' breaker position - confirms this is a new TI device connection, not existing. No receptacle count/type is printed at this tag on A-120 itself; carried as 1 connection pending the power plan's device schedule or a receptacle-count cross-check. (Model line id L-0074.) The model also raised 'no_priced_assembly', 'quantity_needs_plan_count', which the contract has no flag for; recorded here rather than dropped.

Legend row EQ-12 'CCTV Mini Domo: Provide CAT 6A home run to rack. At office camera must point to safe Box.' The matching magenta camera-bubble icon was located once on plan, next to an 'EM3' tag beside the QA/office room cluster in the bottom-left of the floor plate - one confirmed instance. A second, undifferentiated 'CCTV: provide CAT6A home run to rack' icon is also in the legend (implying a retail-floor camera per A-090's EQ-12 'Retail' schedule row) but was not located in the crops read this pass - see coverage_gaps. (Model line id L-0097.) The model also raised 'no_priced_assembly', 'likely_undercount_see_coverage_gaps', which the contract has no flag for; recorded here rather than dropped.

Legend row (tag EQ-20g in the crop, keyed icon) 'Video Recorder+Screen: CAT 6A, and 120V power. Wall-mounted Cabinet.' One legend entry, one wall-mounted cabinet implied; exact ceiling/wall plan position of the cabinet itself was not pinpointed in the crops read (the legend icon column shows the symbol, not a located instance on the floor plan). (Model line id L-0098.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Legend row immediately below 'EQ-25 Safe Box': 'Video Recorder: CAT 6A, and 120V power. Wall-mounted Cabinet.' Read as the recorder that watches the safe box (consistent with EQ-12's note that the office camera must point at the safe box) - one instance, power and data both EC scope. (Model line id L-0099.) The model also raised 'no_priced_assembly', which the contract has no flag for; recorded here rather than dropped.

Detail callout '4 = EQ-35: Mango Sign Interior' on A-150 shows a photo of backlit 'MANGO' letters on a wood-slat wall - the only one of the four interior sign details on this sheet (EQ-33, EQ-34, EQ-35, EQ-36c) that visually reads as illuminated. Note 'FOR SIGNAGE SCHEDULE REFER TO A-090' on this sheet means the actual circuit/VA spec lives there; carried here as a 1-count placeholder pending that cross-check (see coverage_gaps). (Model line id L-0100.) The model also raised 'no_priced_assembly', 'illumination_unconfirmed', which the contract has no flag for; recorded here rather than dropped.

View 3 (Existing Storefront Window Section, 1"=1'-0") on A-210 carries the keyed note 'POWER ELECT. PASS THRU KIT' directly beside 'MANGO EQ-30a SIGN FASTENED AND SECURED TO THE FACE OF THE WALL', at the display-area side of the storefront frame. This names the physical fitting the EC installs to bring power through the wall to the sign cabinet. Read visually and by text extraction (page text is in the PDF's pre-rotation coordinate space; positions transformed via the page's rotation matrix to match the displayed sheet). Cross-references A-200's sign elevation, which shows the same EQ-30a tag and already carries an EC connection-point line (L-0002) pending this sheet's detail - see coverage_gaps for the possible-duplicate flag between the two sheets. (Model line id L-0104.) The model also raised 'no_priced_assembly', 'assembly_id_unmapped', 'possible_duplicate_with_A-200_signage_lines', which the contract has no flag for; recorded here rather than dropped.

View 1 (Storefront Window Display Section, 1"=1'-0") on A-210 carries the keyed note 'POWER ELECT. PASS THRU KIT' directly beside 'MANGO EQ-30b SIGN FASTENED AND SECURED TO THE FACE OF THE WALL'. Same fitting/scope as L-0001, at the second (display-platform) storefront bay. Cross-references A-200's sign elevation (EQ-30b tag, existing line L-0001 on that sheet) - see coverage_gaps for the possible-duplicate flag. (Model line id L-0105.) The model also raised 'no_priced_assembly', 'assembly_id_unmapped', 'possible_duplicate_with_A-200_signage_lines', which the contract has no flag for; recorded here rather than dropped.

View 1 (Storefront Window Display Section) shows the new built-up platform display (06-50, 06-50C 3/4" plywood over flooring, non-illuminated logo at angled surface) with the note 'GC TO PROVIDE POWER AS INDICATED IN SHEET A-120.00'. This is the only power note on the sheet naming 'GC' rather than 'EC'; carried here as one EC connection point per house convention (GC notes for power on architectural finish/equipment sheets are typically executed by the electrical subcontractor), but the responsibility is not confirmed by a matrix on this sheet and A-120.00 (the sheet the note points to) was not in this agent's assigned page set - see coverage_gaps. (Model line id L-0107.) The model also raised 'no_priced_assembly', 'assembly_id_unmapped', 'responsibility_unconfirmed_GC_vs_EC', 'referenced_sheet_A-120.00_not_in_read_set', which the contract has no flag for; recorded here rather than dropped.

Interior Section/Elevation 6 (A-300, top-left of sheet) draws a pictorial wall-mounted exit sign - a rounded-cabinet box with a hanging bracket and the word 'EXIT' legible inside it - directly above the head of a door leading out of the back-of-house corridor. No alphanumeric fixture tag (EX01/EX02) is printed beside the icon on this sheet; job-facts' E-800 Title-24 fixture schedule carries EX01(6 luminaires) and EX02(1 luminaire) for the whole project (7 total exit signs), and the tag-to-instance mapping for this specific door is expected on the E-300/E-400 lighting plan, not on this elevation sheet. Counted as one confirmed exit-sign fixture instance visible on A-300; not a substitute for the E-800 schedule total. Read visually at 8-10x zoom crops because the page's text layer is garbled (same failure mode as A-200). (Model line id L-0108.) The model also raised 'no_priced_assembly', 'schedule_tag_not_on_this_sheet', 'circuit_routing_off_sheet', which the contract has no flag for; recorded here rather than dropped.

On A-310 (page 28), one of six 'Interior Section/Elevation' details shows a wall-mounted EXIT sign pictogram drawn as vector line-art (rendered 'EXIT' lettering, not a text-layer tag) sitting on a visible standoff bracket - two circular mounting fasteners top and bottom holding the sign fixture proud of the finished wall, positioned high on the wall near a ceiling soffit line above a door/opening. Confirmed by rendering the page (set to unrotated/raw coordinate space to match the PDF text layer, mediabox 1728x2592) at 14x zoom over raw rect (680,290)-(780,360) and reading the crop directly. This detail is evidence for the EC's exit-sign INSTALL condition (a bracket-mounted, standoff sign rather than a simple surface box) at at least one of the job's 7 exit-sign locations; the fixture count itself is not re-counted here (see coverage_gaps) - striking this line removes the bracket/support labor and material for that mounting condition, leaving only the bare fixture connection assumed elsewhere. (Model line id L-0110.) The model also raised 'no_priced_assembly', 'new_no_blind_evidence', 'cross_reference_E-800_do_not_duplicate_fixture_count', 'quantity_may_need_scaling_to_all_7_exit_signs_pending_E-300/E-400_mount_type_check', which the contract has no flag for; recorded here rather than dropped.

Hall Elevation (view 7), sheet A-320, 400dpi crop review: a circle-EXIT-circle exit-sign icon is drawn on the corridor wall above the door, at roughly 3'-0" AFF relative to the 9'-5" ceiling line. No adjacent plan tag was legible on this sheet (the sheet's text layer uses a non-standard glyph encoding that defeated text search, and no printed tag is visible on the rendered icon itself). Counted as one exit-sign device toward the job-wide EX01/EX02 total on the E-800 T-24 schedule (7 units total); striking this line does not change the job total by itself since the schedule count already governs, but the sheet confirms one physical location for that total. (Model line id L-0111.) The model also raised 'assembly_id_null_needs_catalog_entry_exit_sign', 'fixture_tag_not_shown_on_this_sheet_reconcile_with_E-800_EX01_EX02_schedule_and_E-300/E-400_plan', 'possible_duplicate_of_count_already_taken_from_E-800_schedule_by_another_sheet_agent', which the contract has no flag for; recorded here rather than dropped.

Restroom Elevation (view 2), sheet A-320, 400/600dpi crop review: a standard duplex-receptacle symbol (two-slot rectangle) is drawn on the wall directly above the lavatory sink (FX-4), left of the mirror/paper-towel dispenser group. This is the only receptacle symbol this agent found across the sheet's seven elevations within the read window; the other restroom elevation (view 3) shows no comparable symbol at the equivalent wall. No panel/circuit/homerun text accompanies it on this sheet -- device count only, to be reconciled against the E-series power plan's own symbol count for this room per coverage_gaps. (Model line id L-0112.) The model also raised 'assembly_id_null_needs_catalog_entry_duplex_receptacle', 'reconcile_against_E-series_power_plan_symbol_count_avoid_double_count', 'branch_circuit_wire_conduit_to_this_device_not_on_this_sheet', which the contract has no flag for; recorded here rather than dropped.

Detail 3 'M-1: Section at Cash Counter' (bottom-left of the sheet) shows a rounded-square device symbol with a dashed centerline crosshair set into the counter's side-wall base, roughly 4" AFF next to the B-10/05-26.1d edge-band callout. This is the recessed outlet mandated by keyed note 26-12.23 and coordinated per 26-12.22. The sheet draws exactly one instance of this symbol; the true count of cash-counter positions (and therefore of this device) is governed by the number of POS positions per counter, which this sheet explicitly defers to A-120/A-140 (see coverage_gaps). Quantity is carried here as 1 representative unit per the typical detail; striking this line drops the only recessed-outlet device found on this sheet. (Model line id L-0113.) The model also raised 'no_priced_assembly', 'quantity_depends_on_POS_count_see_A-120_A-140', 'verify_against_millwork_shop_drawings', which the contract has no flag for; recorded here rather than dropped.

Detail 3 shows the leader-called-out tag '27-21.4' immediately above and sharing the callout cluster with '26-12.22', both pointing into the cash-wrap cabinet/counter zone - i.e. the data drop and the power drop are provisioned at the same location. A-400 itself carries no descriptive text for 27-21.4 (its notes column only spells out 05-25, 06-30.25, 26-12.22, and 26-12.23); the note's content was cross-referenced from A-002 General Notes, read by another sheet-agent this run, which assigns EC the conduit pull and home run with a 6 ft tail, and the owner's vendor the termination. Carried here at 1 representative unit for the same reason as L-0001 - true count depends on POS positions per A-120/A-140. (Model line id L-0115.) The model also raised 'no_priced_assembly', 'quantity_depends_on_POS_count_see_A-120_A-140', 'note_text_cross_referenced_from_A-002_not_on_this_sheet', 'termination_by_owners_vendor_not_EC', which the contract has no flag for; recorded here rather than dropped.

Read note 26-50.21 'Continuous led per schedule' in the Division 26-50 Interior Lighting notes block, cross-referenced to the leader callout '26-50.21' on detail item 5 'Detail @ M-2A Millwork', pointing at the cabinet's vertical corner. The sheet gives no dimensioned run length (no measurement is derivable), so this line is recorded as 1 location rather than a footage; the project's whole-building LED-strip totals (LAL/LAF families) are already carried in the E-800 fixture schedule per job-facts.md and are not re-added here. (Model line id L-0117.) The model also raised 'footage_not_measurable_this_sheet', 'cross_reference_E-300_E-400_for_actual_run_length', 'possible_overlap_with_E-800_fixture_schedule_totals', which the contract has no flag for; recorded here rather than dropped.

Read the 'NOTE: SIGNAGE INSIDE TENANT SPACE' leader with callout '26-50.21' on 'Elevation @ M-2B Millwork' (item 2), pointing to the recessed 'MANGO' logo lettering at the top of the millwork wall. No fixture tag, wattage, or count is given here; counted as 1 signage element. (Model line id L-0118.) The model also raised 'needs_catalog_entry', 'confirm_furnish_by_sign_vendor_vs_EC_see_coverage_gaps', 'confirm_committed_roundel_unlit', which the contract has no flag for; recorded here rather than dropped.

Door schedule row #05 (Retail to Storage, type B, single, notes 1,2,7A,10,12) carries keyed note 7A: 'Door from Retail to Back of House. GC to coordinate with tenant alarm company and to provide the necessary wiring and power. Provide Key pad connected to local alarm on sales side.' Read from the door-schedule table and notes block, rendered at 400-500dpi (the table is not present in the page's extracted text layer -- see sheet.note). Per house default #3/#4 (job-facts.md), the keypad hardware is vendor-furnished/coordinated with the tenant's alarm company; EC scope is the power circuit, box and low-voltage pull to it. Striking this line drops the sales-side keypad connection at this one door. (Model line id L-0119.) The model also raised 'no_priced_assembly', 'needs_assembly_mapping', 'possible_duplicate_of_A-090_A-150_device', which the contract has no flag for; recorded here rather than dropped.

Same keyed note 7A as L-0001 continues: 'Provide push alarm release on employee side.' This is a second, distinct device from the sales-side keypad, on the Back-of-House face of the same door #05 opening. GC/EC scope is wiring and power per note 7A; the alarm-release hardware itself is tenant-alarm-company coordinated. Striking this line drops the employee-side push-alarm-release wiring at this door. (Model line id L-0120.) The model also raised 'no_priced_assembly', 'needs_assembly_mapping', 'possible_duplicate_of_A-090_A-150_device', which the contract has no flag for; recorded here rather than dropped.

Door schedule row #06 (BOH Hallway to Storage, type A, single, notes 2,7C,12; hardware 'ALLEGION CO 100 Satin Chrome(626) LAT lever on Corridor side, Panic bar on Storage side', keylock from Hall side) carries keyed note 7C: 'Door from Service to Back of House. GC to coordinate with tenant alarm company and to provide the necessary wiring and power. Provide Allegion CO 100 or similar. Key pad from exterior for control access.' EC scope per house default is the power circuit, box and low-voltage pull to the keypad; Allegion hardware is vendor-furnished. Striking this line drops door #06's exterior keypad connection. (Model line id L-0121.) The model also raised 'no_priced_assembly', 'needs_assembly_mapping', 'possible_duplicate_of_A-090_A-150_device', which the contract has no flag for; recorded here rather than dropped.

Door schedule row #07 (BOH Hallway to Office, type A, single, notes 2,7B,12; hardware 'ALLEGION CO 100 Satin Chrome(626) LAT lever, Keypad on storage side', keylock from Storage side) carries keyed note 7B: 'Door to Office. Provide Allegion CO 100 or similar. Key Pad exterior / latch, keyless release on interior.' EC scope per house default is power/box/LV pull to the keypad; hardware is vendor-furnished. Striking this line drops door #07's exterior keypad connection. (Model line id L-0122.) The model also raised 'no_priced_assembly', 'needs_assembly_mapping', 'possible_duplicate_of_A-090_A-150_device', which the contract has no flag for; recorded here rather than dropped.

Door schedule row EX-01 (Hall to Exterior, existing 90-min rated door, VIF, Replace/Sec, notes 7C,9,10,12) hardware column reads: 'ALLEGION CO 100 Satin Chrome(626) LAT lever, (KeyPad) on Mall Corridor side, Panic bar on Corridor side, Keypad on Mall Corridor side: CO-100-993R-70-KP-LAT'; Latch = Panic; Lock = 'Electron ic locks with Keypad / Panic locks'. Note 7C (referenced) assigns GC coordination with the tenant alarm company plus wiring and power. Read from the door-schedule table render; EC scope is power/box/LV pull, hardware vendor-furnished per house default. Striking this line drops EX-01's exterior keypad/electric-panic-lock power and low-voltage connection. (Model line id L-0123.) The model also raised 'no_priced_assembly', 'needs_assembly_mapping', 'possible_duplicate_of_A-090_A-150_device', which the contract has no flag for; recorded here rather than dropped.

Door schedule row EX-01's Stop column reads 'Electromagnetic Holder' (against 'Existing' closer, notes 7C,9,10,12 - '90 min rated existing door'). General keyed note 2 on this sheet states: 'All electromagnetic door hold openers to be coordinated with fire alarm system for compliance.' EX-01 is the only door on this schedule whose Stop hardware is an electromagnetic holder (all others use Norton/LCN mechanical closers or none) - this is the device the sorter flagged for this sheet. EC scope per house default is the power circuit and the interconnect wiring to the fire-alarm system that releases the holder on alarm; the holder unit itself and its FA-side programming are vendor/fire-alarm-contractor scope. No fire-alarm riser was in this agent's read set to confirm which trade pulls the interconnect leg - see coverage_gaps. (Model line id L-0124.) The model also raised 'no_priced_assembly', 'needs_assembly_mapping', 'possible_duplicate_of_A-090_A-150_device', 'fa_interconnect_scope_unconfirmed', which the contract has no flag for; recorded here rather than dropped.

Added by house rule: RRE priced this on 4 of 4 past jobs (100%). RRE’s last retail job carried 8 hours of panel safe-off; RRE practice is about 1 hour per panel touched, 8 hours on BYLT and Varley too. Recommended: RRE Components 31784, 8HRS PANELS SAFE OFF, once.